35
I
N
S
T
A
L
L
E
R
S
e
c
t
i
o
n
(
e
n
)
7733595 (01-05/19)
12.4 COMBUSTION TEST (CO
2
%)
For correct boiler operation, the content of (CO
2
- O
2
) in the combustion fumes must observe the tolerances indicated in the
IROORZLQJWDEOH,IWKHYDOXHRI&2
2
- O
2
LVGLႇHUHQWFKHFNWKHHOHFWURGHVDQGWKHLUUHODWLYHGLVWDQFHV,IQHFHVVDU\UHSODFHWKH
HOHFWURGHVDQGSRVLWLRQWKHPFRUUHFWO\,IWKHSUREOHPSHUVLVWVXVHWKHIROORZLQJIXQFWLRQ
G20
G31
CO
2
%
O
2
%
CO
2
%
O
2
%
0D[LPXPSRZHU
Nominal value
8.7
5.4
10.0
6.0
Permitted value
8.2 - 9.3
6.3 - 4.3
9.5 - 10.5
6.8 - 5.2
,JQLWLRQSRZHU
Nominal value
8.7
5.4
10.8
4.8
Permitted value
8.2 - 9.3
6.3 - 4.3
10.3 - 11.3
5.5 - 4.1
0LQLPXPSRZHU
Nominal value
8.8
5.2
10.0
6.0
Permitted value
8.2 - 9.3
6.3 - 4.3
9.5 - 10.5
6.8 - 5.2
The
CO
2
/O
2
values are with the cover closed.
The combustions analisys shall be done using an analyzer regularly calibrated.
During normal operation the boiler performs combustion control cycles. In this phase, CO values higher than 1000 ppm can
occur for brief periods of time.
COMBUSTION ADJUSTMENT FUNCTION (CO
2
%)
This function sets out to partially adjust the value of
CO
2
%
7KHIROORZLQJSURFHGXUHLVXVHG
• Press buttons
and
WRJHWKHUIRUDWOHDVWVHFRQGV:KHQWKHIXQFWLRQLVHQDEOHGWKHGLVSOD\VVKRZV³
On
´IRUDIHZ
VHFRQGVIROORZHGE\SURJUDPPHURZ³
304
´DOWHUQDWHGZLWKWKH
%
RIERLOHUSRZHU
•
$IWHUWKHEXUQHULVOLWWKHERLOHUUHYHUWVWRPD[LPXP'+:SRZHU:KHQWKHGLVSOD\VKRZV
100
LWLVSRVVLEOHWRSDUWLDOO\
adjust the value of
CO
2
%
• press
7KHGLVSOD\VKRZV
00
DOWHUQDWLQJZLWKWKHIXQFWLRQQXPEHU
304
ÀDVKHV
• press
WRUDLVHRUORZHUWKHDPRXQWRI
CO
2
(from -5 to +5).
• press
WR VDYH WKH QHZ YDOXH DQG YLHZ WKH SRZHU YDOXH RQ WKH GLVSOD\ DJDLQ WKH ERLOHU FRQWLQXHV RSHUDWLQJ DW
PD[LPXP'+:SRZHU
This procedure can also be used to adjust the quantity of
CO
2
to the
ignition power
and to the
minimum power
by pressing
after point 5 of the procedure described above.
•
$IWHUVDYLQJWKHQHZYDOXHSRLQWRIWKHSURFHGXUHSUHVV
to take the boiler to its
ignition power
. Wait for the value of
CO
2
WRVWDELOLVHDQGWKHQDGMXVWDVGHVFULEHGLQSRLQWRIWKHSURFHGXUHWKHSRZHUYDOXHLVDQXPEHU!DQG!WKHQ
save (point 5).
• press
again to take the boiler to
minimum power
. Wait for the value of
CO
2
to stabilise and then adjust as described in
SRLQWRIWKHSURFHGXUHSRZHUYDOXH
• to exit the function, press the buttons for at least 6 seconds as described in point 1.
13. GAS VALVE
This appliance does not require any mechanical adjustment on the valve. The system ensures electronic auto-adaptation.
Gas valve key
Pi
Gas supply inlet pressure tap
13.1 GAS CONVERSION METHODS
Only an Authorised Technical Assistance Service can convert boiler operation from
NATURAL GAS
to
LPG
or vice-versa. To
perform calibration, set parameter
P02
as described in the PARAMETER SETTINGS section. Lastly, check the combustion
parameters as described in the SPECIAL FUNCTIONS - CHECKING COMBUSTION PARAMETERS section.
When the gas change is completed the boiler data plate must be amended to indicate the new gas data.
Pi
Summary of Contents for COMPACT E
