background image

With the enclosure installed, you can now re-install the carpeted paneling of the trunk. Be sure and leave the 

amplifier wiring harness exposed approximately 10” from the top portion of the driver’s side carpet when you 

reinstall the carpet. 

This re-installation process can be a bit tricky, as the enclosure now impedes some of your ability to 

effortlessly insert the carpeted panels back into the trunk. Being careful not to damage the subwoofer, 

maneuver the paneling back into the trunk and reconnect all wiring and fasteners as they were originally 

found.

Amplifier Tuning

Head up to the front of the car and turn on the stereo. Put in your favorite CD (not a burned CD, but one that 

was professionally mastered and recorded), and tune in to your favorite track. We recommend using a very 

dynamic type of music, with many types of musical variations within the CD. Make sure that your bass 

settings on your radio are set in the middle or slightly lower. This will decrease distortion and increase the 

overall sound quality in the vehicle.

Make sure all bass and treble settings on your radio are flat, or in the middle.

We’ve roughly adjusted the settings on the amplifier at the factory, but you’ll want to fine tune things 

based on your own listening preferences and sensitivities. 

Gains: 

Begin turning up the volume until you hear the music at a reasonable level and increase the volume slightly 

up to the point that you begin to hear distortion coming from your interior speakers. Now, back down the 

volume until the distortion disappears and stop there. Head back to the trunk and slowly begin adjusting the 

gain(s) of the amplifier until you are content with the amount of bass being produced by the subwoofer 

without any audible distortion of the woofer. Make sure that this blends in with the rest of the music, and 

you’re on your way to a rich, full sound.

When adjusting the amplifier gains, do everything in very small increments

Make sure that you 

increase both gain control knobs at the same rate. 

We recommend 1/8

th

 turn adjustments of the gain to find that sweet spot where there is no distortion and 

 

 

12 of 13

Any reproduction, distribution, modification, or dissemination of these instructions without written permission from Bavarian Soundwerks is 

expressly forbidden and a violation of international copyright law.  Any violation will result in prosecution to the full extent available under the 

law!

© Bavarian Soundwerks, LLC.

2195 Defoor Hills Rd., Suite D, Atlanta, GA 30318

P: 404.963.8857 | 

www.bavsound.com

 

Summary of Contents for BMW E46














Reviews: