manualshive.com logo in svg

Bausch Datacom InduBox GSM M4, Installation & Configuration Manual

Share
Download
Bausch Datacom InduBox GSM M4 Installation & Configuration Manual Download Page 21

WAN

Configuration of the WAN connection over the mobile interface.

General

•

SIM PIN: pin code for the installed SIM card. If the SIM pin is disabled, the 
entered SIM pin will not be sent.

•

Additional init string after startup: at commands that will be executed at startup. 
Only certain AT-commands are allowed, others are discarded.

PPP

•

PPP Authentication type: Choice between CHAP and PAP (Challenge or 
Password Authentication Protocol). PAP&CHAP accepts both CHAP and PAP 
connections. At this moment only PAP&CHAP can be used.

•

APN: Access Point Network name, depends on the service provider, see SIM 
card documentation.

•

APNUN: APN username, some carriers use a user name and password for 
authentication, should be provided by the carrier.

•

APNPW: APN Password, see APNUN

•

MRU: Maximum Receive Unit size, max size of one packet received, standard is 
1500 which is the maximum of an Ethernet packet payload.

•

MTU: Maximum Transmission Unit size, max size of a packet sent, standard is 
1492 which is the maximum PPP packet size. Using a bigger size can cause 
fragmentation and reassembly during transmission.

Summary of Contents for InduBox GSM M4
































Reviews:

No comments

Brands by name

Popular brands

Load more brands