Baumer SXG User Manual Download Page 10

Page: 10 / 64

Product Specifications

6.1 Sensor Specifications

6.1.1 Quantum Efficiency for Baumer SXG Cameras

The quantum efficiency characteristics of monochrome and color matrix sensors for

Baumer SXG cameras are displayed in the following graphs. The characteristic curves for

the sensors do not take the characteristics of lenses and light sources without filters into

consideration, but are measured with an AR coated cover glass.

Values relating to the respective technical data sheets of the sensors manufacturer.

350

450

550

650

750

850

950

1050

Wave Length [nm]

Quantum Ef

ficiency [%

]

SXG (monochrome)

350

450

550

650

750

850

950

1050

Wave Length [nm]

Quantum Ef

ficiency [%

]

SXG (color)

6.1.2 Progressive Scan

All cameras of the SXG series are equipped with Progressive Scan.

Pixel
Active Area (Photodiode)
Storage Area

Microlens

Progressive Scan means that all pixels of the sensor are reset and afterwards exposed

for a specified interval (t

exposure

For each pixel an adjacent storage area exists. Once the

exposure time elapsed, the

information of a pixel is transferred immediately to its storage area and read out from

there.

Due to the fact that photosensitive surface gets "lost" by the implementation of the storage

area, the pixels are mostly equipped with microlenses, which focus the light to the pixels

active area.

Figure 5 ►

Quantum efficiency for
Baumer SXG cameras.

Figure 6 ►

Structure of an imaging
sensor with global shut-

ter (interline).

Summary of Contents for SXG

































































Search results

Summary of Contents for SXG

Reviews:

Related manuals for SXG

Brands by name

Popular brands

Baumer SXG, User Manual

Search results

Summary of Contents for SXG

Reviews:

Related manuals for SXG

Brands by name

Popular brands