Bauer Magnum S Operating Manual Download Page 2

 
 

 

Operating manual 

BAUER Submersible Motor Pump 

/ Version X-2010 

2

 

INTRODUCTION 

 

Thank you very much for purchasing a BAUER submersible motor pump! 

 

We have pleasure to present to you a  

BAUER submersible motor pump 

that features state-of-art technology 

and top quality.  This manual describes how to operate and maintain your 

BAUER submersible motor pump

For reasons of clearness and due to the many possibilities, this manual does not contain everything down into 
detail.  In particular, it cannot possibly deal with every conceivable aspect of operation and maintenance.  
If you need further information or if you are faced with any special problem for which this manual does not give 
sufficient details, please do not hesitate to contact 

BAUER company 

at Kowaldstraße 2, A-8570 Voitsberg for 

the information you need.   
We should also like to emphasise that the contents of this operating manual do neither form part of nor alter in 
any way any previous or existing agreement, promise or legal relationship. Commitments on the part of 

BAUER

 

are based solely on the respective purchase contract, which also contains the complete and only valid warranty 
arrangement. Said contractual terms of warranty are neither extended nor limited by the contents of the present 
operating manual.    
All information contained in the present manual is based on the latest product details available at the time of 
printing. 

BAUER 

reserves the right to change without notice, without assuming any liability!   

BAUER submersible motor pumps

 are designed for safe and reliable performance provided they are 

operated in compliance with the present instruction manual.  In spite of the simplicity of the pump we therefore 
request that you read this manual carefully before putting your 

BAUER submersible motor pump 

into 

operation! All instructions given for handling, operating and servicing the pump must be strictly observed.  On 
condition that these instructions are followed the pump will operate trouble-free to your full satisfaction for many 
years!    
Non-observance of our instructions may cause personal injury or damage to the equipment!    
 
 
 

 
 
 
Please make this manual available to your operating personnel.  You are kindly requested to state the pump 
type and serial number of the submersible motor pump in all inquiries, correspondence, warranty problems or 
parts orders.  These details are specified on the nameplate.      
 
 
 

We hope you will enjoy working with your BAUER submersible motor pump! 

 

 
 
 
 
 
 
 
 

This operating manual is considered an integral part of the submersible motor pump.  Suppliers of new and 
used submersible motor pumps are advised to put down in writing that this manual was handed over together 
with the pump.  

Summary of Contents for Magnum S




















Reviews: