background image

ENGLISH

pag. 47

instruction manual 

for use and maintenance serie MEC, STAR, AGRI

6.4.1 ABSOLUTELY DO NOT USE FOLLOWING OIL TYPES: 

TRASMISSION OIL - USED OIL - HYDRAULIC OIL - VEGETABLE OIL -

OIL FOR GEARS - OIL FOR BRANKES

YOU MUST USE ONLY NEW OIL

6.4.2    GEARBOX OIL

All M-MA-K-KA versions (with gearbox) are equipped with oil into the gearbox.

If you have to change the oil use only ISO VG 460.

6.5  OIL LEVEL

MEC SERIES

STAR/V, AGRI/V SERIES

STAR/F, AGRI/F SERIES

Figure 4

Figure 5

Figure 6

SERIE MEC

For internal lubrication, the minimum oil level is indicated by the notch at the lower end of the level rod (see Figure 4) located on 
the manifold and consequently the maximum level will be reached when the tank is full.

SERIE STAR/V, AGRI/V

For internal lubrication, the minimum oil level is indicated by the total length of the plug with level rod (see Figure 5) situated in the 
back tank and the maximum level will be reached with a full tank. 

Serie STAR/F, AGRI/F

For internal lubrication, the minimum oil level is indicated by the lower notch on the indicator placed at the side of the external tank 

(see Figure 6) and the maximum level will be reached with a full tank

OIL TANK CAPACITY [L]

MEC 1000

MEC 1600

MEC 2000

MEC 3000

MEC 4000

MEC 5000

MEC 6500

MEC 8000

0,6

0,7

1,0

1,2

1,5

2,5

3,1

3,8

MEC 9000

MEC 11000 MEC 13500

STAR/AGRI

STAR-AGRI/F

2,5

3

3,5

3,7

4,3

Table 2

MAX
MIN

MIN

MIN

Summary of Contents for AGRI 60





























Reviews: