background image

ENG

CAUTION

PLEASE READ CAREFULLY THE 
FOLLOWING SAFETY GUIDELINES 
BEFORE OPERATION

Ÿ

Do not use the patio heater for indoors, as it may cause personal 
injury or property damage.

Ÿ

This outdoor heater is not intended to be installed on recreational 
vehicles and/or boats.

Ÿ

Installation and repair should be done by a qualified service 
person.

Ÿ

Improper installation, adjustment, alteration can cause personal 
injury or property damage.

Ÿ

Do not attempt to alter the unit in any manner.

Ÿ

Never replace or substitute the regulator with any regulator other 
than the factory-suggested replacement.

Ÿ

Do not store or use gasoline or other flammable vapors or liquids in 
the heater unit.

Ÿ

The whole gas system, hose, regulator, pilot or burner should be 
inspected for leaks or damage before

Ÿ

use, and at least annually by a qualified service person.

Ÿ

All leak tests should be done with a soap solution. Never use an 
open flame to check for leaks.

Ÿ

Do not use the heater until all connections have been leak tested.

Ÿ

Do not transport heater while it’s operating.

Ÿ

Do not move the heater after it has been turned off until the 
temperature has cooled down.

Ÿ

Keep the ventilation opening of the cylinder enclosure free and 
clear of debris.

Ÿ

Do not paint the radiant screen, control panel or top canopy 
reflector.

Ÿ

Control compartment, burner and circulation air passageways of 
the heater must be kept clean.

Ÿ

Frequent cleaning may be required as necessary.

Ÿ

The LP tank should be turned off when the heater is not in use.

Ÿ

Check the heater immediately if any of the following occurs:

 

- The heater does not reach temperature.

 

- The burner makes popping noise during use (a slight  

 

 

 

noise is normal when the burner is extinguished).

 

- Smell of gas in conjunction with extreme yellow tipping of  

 

the burner flames.

Ÿ

The LP regulator/hose assembly must be located out of pathways 
where people may trip over it or in area where the hose will not be 
subject to accidental damage.

Ÿ

Any guard or other protective device removed for servicing the 
heater must be replaced before operating the heater.

Ÿ

Adults and children should stay away from high temperature 
surface to avoid burns or clothing ignition.

Ÿ

Children should be carefully supervised when they are in the area 
of the heater.

Ÿ

To change the gas cylinder in a amply ventilated area, away from 
any ignition source (candle, cigarettes, other flame producing 
appliances, ...);

Ÿ

To check that the regulator seal is correctly fitted and able to fulfill 
its function showed as photo right;

Ÿ

To not obstruct the ventilation holes of the cylinder housing;

Ÿ

To close the gas supply at the valve of the gas cylinder or the 
regulator after use;

Ÿ

In the event of gas leakage, the appliance shall not be used or if 
alight, the gas supply shall be shut off and the appliance shall be 
investigated and rectified before it is used again;

Ÿ

To check the hose at least once per month

 each time the cylinder 

is changed

or each time before long time no use. If it shows signs 

of cracking, splitting or other deterioration it shall be exchanged for 
new hose of the same length and of the equivalent quality;

Ÿ

The use of this appliance in enclosed areas can be dangerous and 
is PROHIBITED;

Ÿ

Read the instructions before using this appliance. The appliance 
must be installed in accordance with the instructions and local 
regulations.

Ÿ

For connection of hose and regulator,and connection of regulator 
and hose, please refer to photo showed above.

HEATER STAND AND LOCATION

The heater is primarily for outdoor use only. 
Always ensure that adequate fresh air ventilation 
is provided.

Ÿ

Always maintain proper clearance to non 
protected combustible materials i.e. top 100 
cm and sides 100 cm minimum.

Ÿ

Heater must be placed on level firm ground.

Ÿ

Never operate heater in an explosive 
atmosphere like in areas where gasoline or 
other flammable liquids or vapors are stored.

Ÿ

To protect heater from strong wind, anchor 
the base securely to the ground with screws.

GAS REQUIREMENTS

Ÿ

Use propane, butane or their mixtures gas 
only.

Ÿ

The pressure regulator and hose assembly to 
be used must conform to local standard 
codes.

Hose/ Regulator connection and
Regulator / Cylinder connection

11

Summary of Contents for PROMETEO BLACK 11K





















Reviews: