GF Health Products, Inc. - www.grahamfield.com
Zenith Series Service Manual 999-0831-190C DEC. 2013
14
ZENITH SERIES
$OLJQ
$UURZV
3KLOOLSV6FUHZV
DWWDFK6KURXG
6WDII&RQWURO
$VVHPEO\IURP
LQVLGHRIERDUG
6WDII&RQWURO
$VVHPEO\
6KURXG
&DEOH&RYHU
)RRW%RDUG
ZLWKFXWRXW
&DEOH7LH
6WDII&RQWURO
$VVHPEO\
FDEOHWR
PRXQWLQJWXEH
)227
(1'
/RRS0DOH6WDII&RQURO&DEOH
DQGFDEOHWLHWKURXJKPRXQWLQJ
WXEHKROHZLWK)HPDOH6WDII
&RQWURO&DEOH
)HPDOHHQGRI6WDII&RQWURO
$VVHPEO\&DEOHSOXJVLQWR7&DEOH
(QGRI'RXEOH7&DEOHDWIRRWHQG*UH\
7UXQVRQHLWKHUVLGHRI6HDW3DQ
IRUDWWDFKLQJ\RXU+DQG&RQWUROOHU
/RFNLQJ(QG&DSRQ'RXEOH7&DEOH
PLUGGING IN THE FOOTBOARD NURSE/STAFF CONTROL
STEP 1 - ATTACHING THE FOOTBOARD
The APS 9000 bed features a Nurse/Staff Controller in the footboard, however the board is ordered separately with your
bed because of the variety of board styles available. If ordered at the same time as the bed, the Staff Control Assembly
and Shroud Cover will be pre-installed to the Footboard at the manufacturing factory.
STEP 2 - CONNECTING YOUR CABLES
Please refer to DETAIL A shown below.
a. If the Staff Control Assembly is not installed at the
factory you will need to first attach it to the footboard.
b. With the cutout side of the footboard facing outward
as shown, insert the staff control cable through the
large round hole.
c. With the text right-side-up, insert the Staff Control
Assembly into the cutout slot on the footboard and
attach to the board using the two outside small holes
and two screws from your staff control hardware kit.
d. Attach the Shroud Cover over the cable on the
inside of the board using the four remaining screws
from your kit.
e. Insert the T-Cable end (
extending out the foot end
with phone jack
) into the round plug, making sure
the phone jack is seated correctly inside the female
plug (arrow to arrow - See DETAIL B).
f. Screw on the round lock cap onto
the Staff Control’s female plug to
secure (See DETAIL B).
g.
IMPORTANT:
Make sure to tie
off the staff control
cable to the foot-
board mounting
tube with a cable
tie as shown.
DETAIL A:
CLOSEUP OF STAFF
CONTROL CABLE CONNECTION
DETAIL B:
MAKE SURE LOCK
END CAPS ARE
SCREWED ON
SECURELY.
SEE PAGE 10 OF THIS
MANUAL FOR PROPER
ASSEMBLY OF ELBOW
MOUNTING BRACKETS
(TUBES) & FOOTBOARD
Loop Male Staff Control Cable
and cable tie through mounting
tube hole with Female Staff
Control Cable.
Female end of Staff Control
Assembly Cable - plugs into T-Cable
Foot Board
with cutout
Cable Tie
Staff Control
Assembly
cable to
mounting tube
Phillips Screws
attach Shroud
& Staff Control
Assembly from
inside of board
Staff Control
Assembly
Shroud
(Cable Cover)
Locking End Cap on Double T-Cable
End of Double T-Cable at foot end - Grey
(“T” runs on either side of Seat Pan
for attaching your Hand Controller.
