background image

APEX / SILAS 

Pressurized Cabinet 

Safety 

 

Rev. - 

01-3704_7D0001_Manual_APC-SPC_20200617_jrs_en.docx 

Page 9 of 40 

 

Instructions for safe use  

 

 

The user is obliged to take all necessary precautions before using the 
bypass system. 

 

 

The user may only connect elements to an intrinsically safe terminal if they 
have electrical properties which are lower or equal to the properties 
defined in the certificates of the assigned intrinsically safe devices. 

 

 

When setting up the APEX (SILAS) pressurized cabinet with HMIs in the 
front, the special installation conditions concerning impact protection 
must be observed. 
 
The APEX (SILAS) pressurized cabinet is to be installed such that the risk of 
a mechanical danger is low. 

 

 

The outlet must be routed to a safe area if there is a combination of dust 
and gas. 

 

The APEX (SILAS) pressurized cabinet rules out the following 
applications/solutions: 

 

 

The introduction of easily flammable or explosive media, so-called 
containment systems 
 

 

The protection of large electric motors  
 

 

Accessible switch cabinets 

 containers 

 

 

Batteries / storage batteries may not be fitted in an APEX (SILAS) 
pressurized cabinet. The subsequent introduction of batteries /storage 
batteries is also ruled out  
 
Exception: batteries used as support batteries for SPCs, PCs which are 
smaller than 1% of the free protected volume and have a capacity of < 1.5 
Ah. 
 
In this case, the APEX (SILAS) pressurized cabinet must be labelled as 
follows: 
 
WARNING – THIS ENCLOSURE CONTAINS BATTERIES – DO NOT OPEN IF AN 
EXPLOSIVE ATMOSPHERE EXISTS 

 

Summary of Contents for APEX (APC) 07-3704 Series













































Reviews: