background image

1324TK - 1624TK OWNER’S MANUAL                 12/4/14                                      Page 

20

 of 

22

 

 

TRACK TRENCHER TROUBLESHOOTING GUIDE (continued) 

 

D. Tracks fail to turn, but chain rotates 

 
1.

 

Sprocket key sheared 

 
2.

 

Track Drive Valve not fully activated. 

 
 
3.

 

Speed cable broken or disconnected. 

 
4.

 

Pump cable lever loose on shaft. 

 

Replace key and other parts as needed. 

 

Adjust valve cable as shown elsewhere 
in this manual. 

 

Replace or re-connect cable. 

 

Tighten setscrew on pump lever.

 

E. Hydraulic fluid leaks in hydraulic system 

 

1.

 

Fittings are loose. 

 
2.

 

Worn or broken hoses. 

 
3.

 

Hydraulic fluid around chain motor or 

shaft. 
 

Tighten fittings on hoses and adapters. 

 

Replace damaged hoses. 

 

Inspect motor for leaking shaft seal.  
Rebuild or replace motor. 
 

 

F. Foaming hydraulic fluid coming from breather hose. 

 

1.

 

Improper fluid used. 

 
 
 
 
2.

 

Air leaking into fluid. 

 

Verify that hydraulic fluid used had 
antifoaming additives. Tractor 
transmission / hydraulic fluid ISO 68 is 
recommended for use in temperatures 
above +32°F. 

 

Inspect and tighten fittings and clamps 
on pump intake hoses.

 
 

G. Boom does not lift, or does not lower into ground. 

 
1.

 

Boom lift relief valve malfunctioning. 

 

 
2.

 

Boom cylinder piston seal damaged or rod 

bent. 
 
3.

 

Boom pivot bushing seized. 

Adjust relief to 1000 PSI. This may 
require a replacement spring in valve. 

 

Disassemble & replace parts as      
required. 

 

Disassemble, inspect, clean & replace 
parts as required.

Summary of Contents for 1324TK























Reviews: