background image

1324TK - 1624TK OWNER’S MANUAL                 12/4/14                                      Page 

1

 of 

22

 

 

                                                        THE 

           

MODEL 1324TK - 1624TK 

        HYDRAULIC TRACK TRENCHER OWNER’S MANUAL 

 

 
 
CONGRATULATIONS! 
 
You are now the proud owner of the BARRETO trencher. The OPERATOR’S MANUAL is attached 
to the machine. Please study it and this manual to become familiar with the trencher, its 
characteristics, and method of operation. Pay particular attention to the safety and operating 
instructions to prevent personal injury or equipment damage.   
 
If you have any questions or need any replacement parts in the future, please contact us at your 
convenience. Our toll-free phone number, fax and email are listed below. 
 
THANK YOU for your patronage and confidence in BARRETO equipment. 
 
Barreto Manufacturing, Inc. 
Innovative Equipment Engineered to Last 
66498 Hwy 203, La Grande, OR  97850 
(800) 525-7348    (541) 963-7348 
FAX (541) 963-6755 
E-Mail: 

[email protected]

 

Web Site

http://www.barretomfg.com

 

 
 

Machine Identification Record 

 

BARRETO Customer number        

 

 
Machine model number 

       

 

 
Machine serial number 

       

 

 
Engine manufacturer 

       

 

 
Engine model number 

       

 

 
Engine serial number 

       

 

Summary of Contents for 1324TK























Reviews: