Barmesa Pumps 6BSE12036LDS Installation, Operation & Maintenance Manual Download Page 3

Page: 3 / 15

Specifications

DISCHARGE:

6", 125lb, flange horizontal.

SPHERICAL SLD HNDLG:

LIQUID TEMPERATURE:

104° F (40° C) max.

VOLUTE:

Cast iron ASTM A-48 class 30.

WEAR RING:

Bronze. (Only for 6BSE-HLDS series)

MOTOR HOUSING:

Cast iron ASTM A-48 class 30.

SEAL PLATE:

Cast iron ASTM A-48 class 30.

IMPELLER:

6BSE-HLDS series

1 vane (2 for 48 and 60 HP and 3 for

), closed, with vanes on back side.

Cast iron ASTM A-48 class 30.

SHAFT:

416 series stainless steel.

SQUARE RINGS:

Buna-N.

PAINT:

Air dry enamel, water based.

SEAL:

Double mechanical, oil filled chamber. Silicon carbide outboard, carbon ceramic inboard
seal, Buna-N elastomer and stainless steel hardware.

DIAPHRAGM:

Buna-N.

HARDWARE:

300 series stainless steel.

CORD ENTRY:

25 ft of neoprene cord 2/4 G, sealed against moisture.

UPPER BEARING:

Ball, single row, oil lubricated, for radial load.

LOWER BEARING:

Ball, single row, oil lubricated, for radial and thrust load.

MOTOR:

Three phase, NEMA B, oil filled. Requires overload protection to be included in control
panel. Class F insulation.

MOISTURE SENSOR:

Normally open (N/O) included.

TEMPERATURE SENSOR

Normally closed (N/C) included.

OPTIONAL EQUIPMENT:

Impeller trimming, additional cord, tungsten carbide seal, slide rail coupling (SRC-6).

The moisture cord and/or temperature cord is size 18/5, type SO, Ø0.485", for all models.

6BSE18034LDS 18

230

1750

50.6

232

2/3

1.34"

891

6BSE18044LDS 18

460

1750

25.3

116

2/3

1.34"

891

6BSE24034LDS 24

230

1750

62.8

290

2/3

1.34"

928

6BSE24044LDS 24

460

1750

31.4

145

2/3

1.34"

928

6BSE30034LDS 30

230

1750

75.8

364

2/3

1.34"

985

6BSE30044LDS 30

460

1750

37.9

182

2/3

1.34"

985

6BSE36034LDS 36

230

1750

434

2/3

1.34"

992

6BSE36044LDS 36

460

1750

217

2/3

1.34"

992

6BSE48034LDS 48

460

1750

290

2/3

1.34"

1014

6BSE60044LDS 60

460

1750

363

2/3

1.34"

1052

MODEL

HP VOLTS PHASE

RPM

(Nominal)

MAX

AMPS

LOCKED

ROTOR AMPS

NEMA

CODE

CORD

SIZE

CORD

TYPE

CORD

O. D.

WEIGHT

(pounds)

6BSE9036LDS

230

1150

162

2/3

1.34"

897

6BSE9046LDS

460

1150

2/3

1.34"

897

6BSE12036LDS 12

230

1150

162

2/3

1.34"

902

6BSE12046LDS 12

460

1150

2/3

1.34"

902

6BSE18036LDS 18

230

1150

232

2/3

1.34"

917

6BSE18046LDS 18

460

1150

116

2/3

1.34"

917

6BSE24036LDS 24

230

1150

290

2/3

1.34"

961

6BSE24046LDS 24

460

1150

145

2/3

1.34"

961

6BSE30036LDS 30

230

1150

364

2/3

1.34"

1008

6BSE30046LDS 30

460

1150

182

2/3

1.34"

1008

barmesapumps.com

Summary of Contents for 6BSE12036LDS
















Search results

Summary of Contents for 6BSE12036LDS

Reviews:

Related manuals for 6BSE12036LDS

Brands by name

Popular brands

Barmesa Pumps 6BSE12036LDS, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for 6BSE12036LDS

Reviews:

Related manuals for 6BSE12036LDS

Brands by name

Popular brands