Barkey warming center III DTM Service Manual Download Page 29 | Manualshive

Page: 29 / 50

Barkey warming center III DTM Service Manual Download Page 29

Service work

Barkey GmbH & Co. KG - Gewerbestrasse 8 - 33818 Leopoldshoehe – Germany - Head Office: +49 (5202) 9801-0

25

Customer Service: +49 (5202) 9801-30 Fax: +49 (5202) 9801-99 - e-mail: [email protected]

Service manual

Barkey warming center III DTM

Refitting the regulator circuit board:

Refitting the regulator circuit board takes place in reverse order to removal:

►

Re-solder the buzzer cables in place.
CAUTION: Ensure the cable polarity is correct.

►

Locate the regulator circuit board onto the assembly frame bolts.

►

Fix the regulator circuit board with the four fixing nuts and the serrated lock washers.

►

Reconnect the three pin-and-socket connectors to the regulator circuit board.

►

Refix the cover plate (see Chapter 7.2).

►

Refit the heater insert (see Chapter 7.2).

WARNING

A technical safety inspection and an adjustment must be carried out after a regu-
lator circuit board has been replaced.

«
...
27
28
29
30
31
...
»

Summary of Contents for warming center III DTM



















































Reviews:

No comments