manualshive.com logo in svg

Barkey warming center III DTM, Service Manual, Page: 28 / 50

Share
Download
Barkey warming center III DTM Service Manual Download Page 28

Service work

24

Barkey GmbH & Co. KG  -  Gewerbestrasse 8  -  33818 Leopoldshoehe  -  Germany  -  Head Office: +49 (5202) 9801-0

Customer Service: +49 (5202) 9801-30  Fax: +49 (5202) 9801-99  -  e-mail: [email protected]

Service manual
Barkey warming center III DTM

7.3 

Replacing the regulator circuit board

Removal:

►

 

Remove the heater insert (see Chapter 7.2).

►

 

Remove the cover plate (see Chapter 7.2).

►

 

Now pull the three pin-and-socket
connectors off the regulator circuit
board.

Figure 17: Pin-and-socket connectors on regulator circuit board

►

 

Remove the four regulator circuit
board fixing nuts.

Figure 18: Regulator circuit board fixing nuts

►

 

Pull the regulator circuit board off the bolts on the assembly frame.

►

 

Turn the regulator circuit board round
and solder the buzzer cables off.
CAUTION:
Ensure the cable polarity is correct.
Note which cable colour is connected
to which terminal.

Figure 19: Buzzer connection

+

Summary of Contents for warming center III DTM



















































Reviews:

No comments