![background image](http://html1.mh-extra.com/html/barco/thor-series/thor-series_installation-manual_4055863016.webp)
R5906788-03
Thor series
16
•
Lenses, shields or screens shall be changed if they have become visibly damaged to such an extent that
their effectiveness is impaired. For example by cracks or deep scratches.
•
The associated Laser Safety responsible of the unit must evaluate the setup before the unit may be
started.
•
Never point or allow light to be directed on people or reflective objects within the HD zone.
•
If the unit is shut down, remove the key control from the system; avoiding unauthorized startup.
•
All operators shall have received adequate training and be aware of the potential hazards.
•
Strictly minimize the number of people who have access to the unit. The unit may never be operated
without permission of the responsible for laser safety.
•
When the projected light causes a dangerous situation the operator must hit the beam stop button which is
located close to the control panel. The beam stop removes all power from the laser power supplies.
•
Don't put your hand in front of the beam.
•
Do not clean the port window when the projector is switched on.
•
Position the hoses of the cooling system so that they will not be tripped over, pulled, or contact hot
surfaces.
On servicing
•
Do not attempt to service this product yourself, as opening or removing covers may expose you to
dangerous voltage potentials and risk of electric shock.
•
Refer all servicing to qualified service personnel.
•
Attempts to alter the factory-set internal controls or to change other control settings not specially discussed
in this manual can lead to permanent damage to the projector and cancellation of the warranty.
•
Remove all power from the projector and refer servicing to qualified service technicians under the following
conditions:
-
When the power cord or plug is damaged or frayed.
-
If liquid has been spilled into the equipment.
-
If the product has been exposed to rain or water.
-
If the product does not operate normally when the operating instructions are followed. Adjust only those
controls that are covered by the operating instructions since improper adjustment of the other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to normal operation.
-
If the product has been dropped or the cabinet has been damaged.
-
If the product exhibits a distinct change in performance, indicating a need for service.
•
Replacement parts: When replacement parts are required, be sure the service technician has used original
Barco replacement parts or authorized replacement parts which have the same characteristics as the
Barco original part. Unauthorized substitutions may result in degraded performance and reliability, fire,
electric shock or other hazards. Unauthorized substitutions may void warranty.
•
Safety check: Upon completion of any service or repairs to this projector, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
To prevent projector damage
•
The air filters of the projector must be cleaned or replaced on a regular basis. Cleaning the booth area
would be monthly-minimum. Neglecting this could result in disrupting the air flow inside the projector,
causing overheating. Overheating may lead to the projector shutting down during operation.
•
The projector must always be installed in a manner which ensures free flow of air into its air inlets.
•
If more than one projector is installed in a common projection booth, the exhaust air flow requirements are
valid for EACH individual projector system. Note that inadequate air extraction or cooling will result in
decreased life expectancy of the projector as a whole as well as causing premature failure of the lasers.
•
In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic
Compatibility (EMC) and safety requirements, it should always be operated with all of it's covers in place.
•
Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product
and to protect it from overheating, these openings must not be blocked or covered. The openings should
never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should
never be placed near or over a radiator or heat register. The device should not be placed in a built-in
installation or enclosure unless proper ventilation is provided.
•
Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and
remove all power from the projector. Do not operate the projector again until it has been checked by
qualified service personnel.
Summary of Contents for Thor Series
