![background image](http://html1.mh-extra.com/html/barco/thor-series/thor-series_installation-manual_4055863107.webp)
R5906788-03
Thor series
107
As a result the backlight of the Light button starts blinking green indicating the projector is in CONDITIONING
mode. The laser status light on the top of the projector flashes a few times and then lights up continuously
white.
Once the projector is conditioned the backlight of the Standby button is changed to continuous green. Now the
lasers are active and light can come out of the projector. The status light of the projector remains green and
the status light of the lasers remains white.
5.
Press the
DOWSER
button on the Local Keypad or use the Communicator to open the dowser.
Note:
The state of the dowser (open or closed) when starting up the projector will be the same as
when the projector was switched off. This procedure assumes that the dowser was closed .
CAUTION:
See user's guide of the Communicator Touch Panel to operate and control the Thor
series.
When for any reason a restart of the projector is required, the content server should be restarted
also.
10.2 Switching the Thor series projector OFF
About the switch off process
To switch off the Thor series projector in a safe manner to protect the internal electronics (avoid moisture due
to warming up) the temperature inside the sealed compartments has to be brought back to ambient in a
controlled manner. This process is called
deconditioning
.
How to switch the Thor series OFF?
1.
Press the Standby button for three seconds on the Local Keypad or use the Communicator Touch Panel to
switch the projector from OPERATIONAL mode to STANDBY mode. As a result the lasers are deactivated (if
activated) and the projector starts to deconditioning the sealed compartments.
Caution:
Do not switch off the power from the projector until the laser status light is off. Also make sure
not to power off the chiller(s). The chiller(s) should remain on as long as the projector is powered on.
2.
Switch the projector OFF with the power switch.
Keep in mind that it can take up to 10 minutes to start the lasers again after they were switched off.
If there are only 30 to 45 minutes between the shows it
’
s advisable to keep the lasers on with
dowser closed. When the dowser is closed the lasers are automatically dimmed.
Summary of Contents for Thor Series
