Barco SIM 7C R9011206 Service Manual Download Page 25

Page: 25 / 44

5. Projector software (firmware)

5. PROJECTOR SOFTWARE (FIRMWARE)

Overview

•

Description of the software

•

Projector software version

•

Upgrading the projector software

5.1

Description of the software

Description

The

projector software

consists out of different parts:

•

projector application

•

FPGA con

gurations

•

operating system (eCos)

•

boot loaders

•

drivers and

rmware

The projector software can be upgraded: one single executable

le is used as an upgrade tool. This Windows application uploads

the new software,

le by

le, and veri

es that each upload is successful.

5.2

Projector software version

Necessary tools

No tools.

How to display the projector software version?

1. Press

MENU

to activate the tool bar

2. Press

→

to select

General

3. Press

↓

to drop down the General menu

4. Use

↓

to select

Identi

cation

Image 5-1

5. Press

ENTER

In the appearing window, the projector software version is mentioned.

Image 5-2

R59770119 SIM 7C 28/05/2008

Summary of Contents for SIM 7C R9011206













































Search results

Summary of Contents for SIM 7C R9011206

Reviews:

Related manuals for SIM 7C R9011206

Brands by name

Popular brands

Barco SIM 7C R9011206, Service Manual

Search results

Summary of Contents for SIM 7C R9011206

Reviews:

Related manuals for SIM 7C R9011206

Brands by name

Popular brands