Barco SIM 7C R9011206 Service Manual Download Page 22 | Manualshive

Page: 22 / 44

background image

4. Covers

Image 4-12
Lamp cover: removing

3. Remove the lamp cover

Image 4-13
Lamp cover: removed

4.5.2

Installing the lamp cover

Necessary tools

Torx screwdriver T10

How to install the lamp cover?

1. Put the lamp cover in the right position

2. Slide the lamp cover upward and to the front side of the projector (1)

Note:

If the top-right cover is already installed, the joggles of the lamp cover must slide behind it (2).

Image 4-14
Lamp cover: slide it in its correct position

3. Tighten the 3

fi

xing screws

18

R59770119 SIM 7C 28/05/2008

«
...
20
21
22
23
24
...
»

Summary of Contents for SIM 7C R9011206













































Reviews:

No comments

Related manuals for SIM 7C R9011206

Brand: Eiki Pages: 51

Brand: HQ Pages: 2

Brand: Dukane Pages: 8

Brand: Renkforce Pages: 88

Brand: Eiki Pages: 56

The Premiere LSP7TFAXXE

Brand: Samsung Pages: 56

Brand: Hitachi Pages: 64

Brand: Hitachi Pages: 136

Brand: Hitachi Pages: 31

Brand: Hitachi Pages: 104

CP-X2010 series

Brand: Hitachi Pages: 3

Brand: Canon Pages: 25

Brand: Canon Pages: 12

LV-5220 - Multimedia Projector SVGA

Brand: Canon Pages: 6

Brand: Canon Pages: 2

Brand: Canon Pages: 119

Brand: Canon Pages: 4

Brand: Canon Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands