- 22 -
Error Code Description list
Barco RLM W6 error message
No. Error Message
Led status Description
0
ErrMsgOverTempInlet:
7
Inlet (Ti) sensor over temperature (53 C)
1
ErrMsgOverTempDMD:
7
DMD(Tc) sensor over temperature(69 C)
2
ErrMsgOverTempLamp1:
7
Lamp 1 over temperature
3
ErrMsgOverTempLamp2:
7
Lamp 2 over temperature
4
ErrMsgOverTempBallast1:
7
Ballast 1 over temperature
5
ErrMsgOverTempBallast2:
7
Ballast 2 over temperature
6
ErrMsgFanInitError:
8
Fan error in powering on the projector
7
ErrMsgFan1RotateError:
6
Fan 1 rotation error
8
ErrMsgFan2RotateError:
6
Fan 2 rotation error
9
ErrMsgFan3RotateError:
6
Fan 3 rotation error
10
ErrMsgFan4RotateError:
6
Fan 4 rotation error
11
ErrMsgFan5RotateError:
6
Fan 5 rotation error
12
ErrMsgFan6RotateError:
6
Fan 6 rotation error
13
ErrMsgFan7RotateError:
6
Fan 7 rotation error
14
ErrMsgFan8RotateError:
6
Fan 8 rotation error
15
ErrMsgDMDInitFail:
8
DDP3021 communication failure in powering on the projector
16
ErrMsgLampInitFail:
4
When one lamp fails and one lamp successes on starting the projector, it will
takes
6 times
to ignite the fail lamp to make sure the lamp is really failed
17
ErrMsgLampLitFail:
4
Lamp 1 shut down while system is working
18
ErrMsgBallastUartError:
8
Ballast 1 UART communication failure
19
ErrMsgExGpioFail:
8
PCF 8575 external GPIO communication failure
20
ErrMsgInterLockOpen:
5
Lamp door open when system is powered on
21
ErrMsgGF9450NoResponse:
8
Gennum SPI communication failure in powering on the projector
22
ErrMsgSystemI2cFail:
8
System hardware I2C communication failure
23
ErrMsgSoftwareI2cFail:
8
System software I2C communication failure
24
ErrMsgEepromFail:
8
EEPROM check failure
25
ErrMsgEdidFail:
8
EDID check failure
26
ErrMsgEepVersionFail:
8
EEPROM version check failure
27
ErrMsgRstGennum:
8
GSPI bus communucation failure but not entering error state (only being
recorded in log)
28
ErrMsgFan9RotateError:
6
Fan 9 rotation error
29
ErrMsgFan10RotateError:
6
Fan 10 rotation error
Summary of Contents for RLM W6
