System manual MeDis 5MP1HM
51
Setting the Resolution of Your 5MP1HM
Once you have completed the installation of the display driver, you
need to set the resolution for each display connected to each
controller.
1. To set the resolution for your high resolution display(s), right click
on the desktop and select
Properties
.
SPECIAL NOTE:
If you are using the VGA capabilities of your
BarcoMed 5MP1HM, the resolution for the virtual display will be set
to a VGA resolution of 640 x 480 pixels. If you are NOT using the
VGA capabilities of your BarcoMed 5MP1HM, the display may not
be enabled yet. To enable the display
check
the
Extend my
Windows desktop onto this monitor
checkbox. Do not click the
Apply
button at this time.
2. Select the
Settings
tab (see figure 26 on the next page). Now
select the
rectangle
that represents the first high resolution display
attached to the BarcoMed Display Controller you are working with.
SPECIAL NOTE:
If you are using the VGA capabilities of your
BarcoMed Display Controller, the resolution for the first display will
still be set to a VGA resolution of 640 x 480 pixels. If you are NOT
using the VGA capabilities of your BarcoMed Display Controller,
the display may not be enabled yet. To enable the display
check
the
Extend my Windows desktop onto this monitor
checkbox.
Do not click the
Apply
button at this time.
Note:
Since Windows XP will not let you detach the primary
display, you may need to temporarily make another display the
primary display.
3. For the display which is still attached click on the
Advanced
Button.
4. Select the
Adapter
tab and then click on the
List All Modes
button. Select the resolution and refresh rate that your high
resolution display supports from the dialog box and click
OK
.
Note:
In the Adapter box, the Adapter string shows if this display is
the First View or the Second View attached to the Display
Controller. Please make a note of this, so that you can arrange the
displays in the correct order later.
5. Click
OK
on the bottom of the Adapter Control Panel. If the
OK
button on the bottom of the Adapter Control Panel is not
visible, press
CTRL+Enter
to select
OK
.
6. Click
OK
in the Windows will now apply your new desktop
settings dialog box. Your high resolution display(s) should now
synchronize and display the Windows desktop.
7. Click
Yes
when asked, Your desktop has been reconfigured. Do
you want to keep these settings?
BarcoMed driver and software installation
Summary of Contents for MeDis 5MP1HM
