2. General
2.5
Installation process overview
Let the projector acclimatize after unpacking. Neglecting this may result in a startup failure of the Light Pro-
cessor Unit.
Setup from A to Z
After you have unpacked and checked the projector you can start with the installation process of your Barco HDQ 4K35. This chapter
gives you an overview of all the different stages in the installation process which you have to follow to set your HDQ 4K35 up and
running. Each stage is brie
fl
y described and refers to more detailed step by step procedures in this manual. Use this overview as a
checklist to ensure that you have followed all stages in the setup process of your HDQ 4K35.
What has to be done?
1.
Check if all installation requirements are ful
fi
lled
such as the environment conditions of the installation area, electrical facili-
ties, etc. For more info see chapter "Installation requirements", page 10.
2.
Installation of the Lamp House.
The Lamp House is delivered separately from your projector. Unpack the Lamp House and
install it in your projector. See chapter "Installation of the Lamp House", page 18.
3.
Installation of the Lens.
Select and install an appropriate lens for your speci
fi
c situation. Don’t forget to install the additional
lens
fi
xation mechanism. See chapter "Installing the lens
4.
Connect the projector with the power net.
Choose the correct power input con
fi
guration according to your local power net
and connect the projector. See chapters "Access to the power connection", page 19, and "Connecting the projector with the
power net", page 22. If necessary connect the projector electronics with a UPS. See chapter "Connecting a UPS to the projector
electronics", page 23.
5.
Power input set up and Electrical connection with the power net
. See chapter "Power input setup of the HDQ 4K35", page
20 and "Connecting the projector with the power net", page 22.
6.
Installation of the Communicator Touch Panel
. See chapter XXXXXX.
7.
Physical installation of the projector.
Position your HDQ 4K35 in landscape or portrait mode, see chapter "Landscape and
portrait mode", page 25. If necessary, choose to stack multiple projectors, either in a standing (table mount) or hanging (ceiling
mount) con
fi
guration, see chapter "Stacking multiple projectors", page 27.
8.
Switch ON the projector.
See "Switching ON the HDQ", page 67.
9.
Connect your source to the appropriate input.
See "Source input ports of the Barco HDQ 4K35 projector", page 60.
10.
Select the input to which the source is connected.
Use Communicator to make the selection.
11.
Alignment of the projected image on the screen
. The projector can now be switched on to project its
fi
rst image (test pattern)
on the screen. Then the image can be aligned with the screen size of the application. Follow the next steps to achieve that:
a) Place the
ON/OFF
switch of the projector in the ”I” position. As a result the projector starts to initialize. The status lights of
the projector lights up GREEN once the projector is initialized.
b) Press the
STANDBY
button on the local keypad to activate the lamp.
c) Press the
DOWSER
button on the local keypad to open the dowser of the projector. The dowser is open if the color of the
DOWSER button is GREEN.
d) Press the
TEST PATTERN
button on the local keypad to project one of the internal test patterns of the projector on the screen.
e) Use the lens
ZOOM
,
SHIFT
and
FOCUS
buttons on the local keypad the match the projected image with the screen. Tilt the
projector in case you can not SHIFT the image completely upon the screen.
12.
Resetting the lamp parameters
. The lamp parameters MUST be updated after each installation of an xenon lamp inside the
lamp house or when replacing the complete lamp house. Neglecting this update will result in poor performance and short life
time of the xenon lamp. Consult the Communicator software manual section
Installation
→
Lamp
.
13.
Realignment of the xenon lamp in its re
fl
ector
. For optimal performance of the xenon lamp it is required to realign the lamp
after installation in the lamp house. See "Realignment of the lamp in its re
ector", page 78 for more information.
14.
Adjusting the light path
. Normally the lens holder and the convergence of the projector is perfectly adjusted at the factory.
Nevertheless, some applications require a readjustment of the lens holder, convergence or both. See procedure "Scheimp
15.(if applicable)
Align the projected images of the stacked projectors.
See chapters "Adjusting the multifunctional frame", page
30 and "Aligning stacked projectors", page 34.
16.
Projection of a source signal
. Apply a single or dual channel DisplayPort (DP) source to the input ports of the projector and
start up the projector. See chapter "Source input ports of the Barco HDQ 4K35 projector", page 60. Use the Communicator Touch
Panel to con
fi
gure the applied source. See the user guide of the Communicator Touch Panel for more detailed information.
16
R5905823 HDQ 4K35 30/11/2015
Summary of Contents for HDQ 4K35
