![background image](http://html1.mh-extra.com/html/barco/hdf-w30lp/hdf-w30lp_user-and-installation-manual_4170176126.webp)
13. Input
3. Use the
▲
or
▼
key to select
Create
.
Press
ENTER
to open the creation menu.
4. Fill out the
Timings
section.
Use the
▲
or
▼
key to select a setting.
Use the
◄
or
►
key to change the value
or press
ENTER
to open the speci
fi
c adjustment menu. Follow the adjustment method as described in "Navigation and adjust-
ments", page 106.
The following timings must be entered:
-
Active Pixels
: horizontal resolution
-
Active Lines
: vertical resolution
-
Frequency
(Hz): amount of frames per second
5. Select the calculation method to obtain the correct (standard) video timings.
Possible selections:
-
CVT
: Coordinated Video Timings
-
CVT RB
: Coordinated Video Timings Reduced Blanking
-
CVT MB
: Coordinated Video Timings Minimum Blanking (not a standard)
-
GTF
: Generalized Timing Formula
6. Select the
Options
.
If necessary, scroll down to see extra options.
Select or clear the check boxes.
Image 13-27
EDID
fi
le creation, options
The following options are possible:
-
Stereo
: this check box is currently not in use. You can leave it unchecked.
-
Deep color
: select this box in case of a 12 bit color signal. In this case, the Single Link pins of the DVI connector convey the
eight most signi
fi
cant bits, while the Dual Link pins convey the four least signi
fi
cant bits.
-
Analog: this check box makes the selection between DVI digital or DVI analog. When checked, DVI analog is active.
7. A
fi
lename is proposed. This proposed name contains the resolution, calculation, frequency and a D or A for digital or analog.
To change the
fi
le name, select
Filename
and press
ENTER
to open the edit box.
Click inside the edit box and change the name to the desired name.
8. Select
Create
and press
ENTER
to create the new custom
fi
le.
13.9.3 Delete a custom EDID
fi
le
Standard EDID
fi
les cannot be deleted.
How to delete
1. Press
Menu
on the remote control (RCU) or on the local keypad to activate the menus and select
Input
→
EDID
→
Delete
.
2. Press
ENTER
to open the EDID list with custom
fi
les.
122
R5906730 HDF WLP SERIES 01/08/2017
Summary of Contents for HDF-W30LP
