background image

6

B. Power cord with ANSI 73.11 plug

:

The wires of the power cord are colored in accordance with the following code.

Green/yellow:

ground

White:

neutral

Black:

line (live)

3. 

Power ratings : 0.25A /100-240V

4

. Do not allow anything to rest on the power cord. Do not locate this product  where persons will

walk on the cord.

To disconnect the cord, pull it out by the plug. Never pull the cord itself.

5

. If an extension cord is used with this product, make sure that the total of the ampere ratings on

the products plugged into the extension cord does not exceed the extension cord ampere

rating.

6

. Never push objects of any kind into this product through cabinet slots as they may touch

dangerous voltage points or short  out parts that could result in a risk of fire or electrical shock.

Never spill liquid of any kind on the product. Should any liquid or solid object fall into the

cabinet, unplug the set and have it checked by qualified service personnel before resuming

operations.

7

. Lightning - For added protection for this video product during a lightning storm, or when it is left

unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent

damage to the projector due to lightning and AC power-line surges.

Safety Instructions

On installation

For a safe installation, refer to setup-requirements doc/installation doc.

On servicing

Do not attempt to service this product yourself, as opening or removing covers may expose you

to dangerous voltage potentials and  risk of electric shock!

Safety indication on the product

The lightning flash with an arrowhead

within a triangle is intended to tell the user

that parts inside this product may cause a

risk of electrical shock to persons.

The exclamation point within a triangle is

intended to tell the user that important

operating and/or servicing instructions are

included in the technical documentation for

this equipment.

Summary of Contents for Duet R9898140





















Reviews: