![background image](http://html1.mh-extra.com/html/barco/dp2k-12c/dp2k-12c_installation-manual_3917263013.webp)
2. General
2. GENERAL
About this chapter
Read this chapter before installing your DP2K C-series projector. It contains important information concerning installation require-
ments for the DP2K C-series projector, such as minimum and maximum allowed ambient temperature, humidity conditions, required
safety area around the installed projector, required power net, etc.
Furthermore, careful consideration of things such as image size, ambient light level, projector placement and type of screen to use
are critical to the optimum use of the projection system.
About DP2K C-series projectors
This manual can be used for the following projectors :
•
DP2K-12C
•
DP2K-15C
•
DP2K-20C
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guar-
antee. Observing the speci
fi
cation mentioned in this chapter is critical for projector performance. Neglecting
this can result in loss of warranty.
Overview
•
•
•
•
2.1
Installation requirements
Environment conditions
Table below summarizes the physical environment in which the DP2K C-series projector may be safely operated or stored.
Environment
Operating
Non-Operating
Ambient Temperature
10 °C (50 °F) to 35 °C (95 °F)
-15°C (5°F) to 60°C (140°F)
Humidity
5% to 85% RH Non-condensed
5% to 95% RH Non-Condensed
Altitude
-60 (-197Ft) to 3000m (9843Ft)
-60 (-197Ft) to 10000m (32810Ft)
Let the projector acclimate to the ambient temperature after unpacking. Neglecting this may result in a startup
failure of the Light Processor Unit.
Cooling requirements
The projector is fan cooled and must be installed with suf
fi
cient space mainly in the front of the projector head, minimum 20 cm (8
inch) to ensure suf
fi
cient air
fl
ow. It should be used in an area where the ambient temperature, as measured at the projector head
air inlet and at the power unit air inlet, does not 35°C (+95°F).
The installation of an
exhaust system
is
MANDATORY
. The installed exhaust blower must remove an air volume of minimum
6,65
m
3
/min (235 CFM)
.
Power requirements
The DP2K C-series projector operates from a nominal mono phase power net with a separate earth ground PE. A label on the
projector indicates the nominal line voltage for which the projector was set at the factory.
Projector
Power requirements
DP2K-12C
200–240 VAC, 50–60 Hz, 15 amps at 200 VAC
DP2K-15C
200–240 VAC, 50–60 Hz, 20 amps at 200 VAC
DP2K-20C
200–240 VAC, 50–60 Hz, 26 amps at 200 VAC
R5905050 DP2K C-SERIES 10/07/2012
7
Summary of Contents for DP2K-12C
