![background image](http://html1.mh-extra.com/html/barco/dp2k-12c/dp2k-12c_installation-manual_3917263014.webp)
2. General
The power cord required to connect the projector with the power net is not delivered with the projector. It is the responsibility of the
customer to provide the correct type of power cord. The cross-sectional area of the conductors in the power supply cord shall not
be less than 4 mm² or 10 AWG, minimum 300V.
To protect operating personnel, the National Electrical Manufacturers Association (NEMA) recommends that the instrument panel
and cabinet be grounded. In no event shall this projector be operated without an adequate cabinet ground connection.
The AC supply must be installed by a quali
fi
ed electrician in conformance to local codes. Hardware, wire sizes and conduit types
must comply with local codes.
UPS requirements
The Uninterruptible Power Supply (UPS), also known as a Continuous Power Supply (CPS), must have an output voltage of 200-
240V at 50-60Hz and must be capable of delivering an output current of 5,5 amperes.
The connection between the UPS unit and the UPS inlet of the projector must be done with a certi
fi
ed AC power supply cord of
minimum 0,75 mm² or 18 AWG and minimum 300V.
C
AUTION
:
The 200–240V power outlet (UPS OUTLET) of the projector may not be used to provide the UPS
unit with power! The UPS OUTLET of the projector may only be used for connection to the UPS INLET of the
projector.
The DP2K C-series projector does not have a built in UPS unit.
Projector weight
Do not underestimate the weight of the Barco DP2K C-series projector.
The projector weights are without lens. Be sure that the pedestal on which the projector has to be installed is capable of handling
fi
ve (5) times the complete load of the system.
Projector
Weight
DP2K-12C
±100 kg (±200 lb.)
DP2K-15C
±102 kg (±225 lb.)
DP2K-20C
±102 kg (±225 lb.)
Barco offers a pedestal for the DP2K C-series projector. This universal pedestal allows a solid and easy setup
of the projector. The universal pedestal has a separate compartment to install the UPS unit for the DP2K
C-series projector. Futhermore, the universal pedestal contains a standard 19” rack to build in the projector
peripherals such as alternative content switchers (e.g. ACS-2048)
2.2
Unpacking the projector
What has to be done ?
At delivery the projector is packed in a carton box upon a wooden pallet and secured with banding and fastening clips. Furthermore,
to provide protection during transportation, the projector is surrounded with foam. Once the projector has arrived at the installation
site, it has to be removed from the carton box and wooden pallet in a safe manner without damaging the projector.
After unpacking let the projector acclimate to the room temperature which must be higher then 10°C (50°F)
and lower then 35°C (95°F). Neglecting this may result in a start up failure of the Light Processor Unit.
Necessary tools
•
8 mm Allen wrench.
•
13 mm open end wrench.
•
17 mm open end wrench.
How to unpack the projector ?
1. Remove the banding around the carton box, by releasing the fastening clips as illustrated, and open the box.
8
R5905050 DP2K C-SERIES 10/07/2012
Summary of Contents for DP2K-12C
