background image

 

explosive materials. In such location, only an approved Ex-protection model is allowed for use, but any attempt to 
assemble or disassemble it is strictly prohibited. 

2.

 

  Do not operate the product near or in any blasting area. 

3.

 

  Do not operate the product near any medical or electronic equipment vulnerable to RF signals. 

4.

 

  Do not hold the product while driving. 

5.

 

  Do not operate the product in any area where wireless communication equipment is completely prohibited. 

Important Tips 

To help you make better use of the product, be sure to observe the following instructions: 
1.

 

  Do not use any unauthorized or damaged accessories. 

2.

 

  Keep the product at least 2.5 centimeters away from your body during transmission. 

3.

 

  Do not keep the product receiving at high volume for a long time. 

4.

 

  For vehicles with an airbag, do not place the product in the area over the airbag or in the airbag deployment area. 

5.

 

  Keep the product and its accessories out of reach of children and pets. 

6.

 

  Please operate the product within the specified temperature range. 

7.

 

  Continuous transmission for a long time may lead to heat accumulation within the product. In this case, please keep it at 

a proper location for cooling. 

8.

 

  Handle the product with care. 

9.

 

  Do not disassemble, modify or repair the product and its accessories without authorization. 

Precautions for Batteries 

Charging Prohibitions 

To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions: 
1.

 

Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres and other 

flammable or explosive materials. 

2.

 

Do not charge your battery that is wet. Please dry it with a soft and clean cloth prior to charging. 

3.

 

Do not charge your battery suffering deformation, leakage and overheating. 

Summary of Contents for UV-17R Series










































Reviews: