background image

 

Chapter 1. Getting Started                                                                                                                     

1.1

 Regulations and Safety Warnings   

FCC Regulatory Conformance 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

 

of FCC 

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. 
This equipment generates and can radiate radio frequency energy. If not installed and used in accordance with the 
instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference 
will not occur in a particular installation. Verification of harmful interference by this equipment to radio or television 
reception can be determined by turning it off and then on. The user is encouraged to try to correct the interference by one 
or more of the following measures:   

Reorient or relocate the receiving antenna.   

Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.     

Consult the dealer or an experienced radio/TV technician for help.   

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to 
operate the equipment.     
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause 
harmful interference.       

WARNING

 

MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED 

UNDER FCC RULES AND FEDERAL LAW. 

Compliance with RF Exposure Standards   

The radio complies with the following RF energy exposure standards and guidelines: 

 United States Federal Communications Commission, Code of Federal Regulations; 47 CFR § 1.1307, 1.1310 and 2.1093   

 American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada 

Summary of Contents for UV-17R Series










































Reviews: