background image

Bante520 Portable Conductivity Meter 

11 

 

Temperature Calibration 

During the measurement process, if the temperature reading displayed differs from that of an accurate thermometer, the meter needs to be calibrated. 
1. 

Connect the temperature probe to the meter and place into a solution with a known accurate temperature. 

2. 

Press and hold the 

o

C

 key to enter the temperature setting mode. 

3. 

Press the 

 or 

 key to set the temperature value. 

4. 

Press the 

Enter

 key to confirm. Calibrating is completed. 

 

 

 

  During the setting process, press the 

 or 

 key once, the setting value will increase or decrease by 0.1. Press and hold the 

 or 

 key, the 

 

setting value will increase or decrease by 1. 

 

Conductivity Measurement 

1. 

Rinse the conductivity electrode thoroughly with distilled water. 

2. 

Place the electrode into the sample solution, stir the electrode gently. 

3. 

Record the measured value when the reading is stable. 

 

Auto-Hold 

The  meter  contains  an  Auto-Hold function.  If  enabled,  the  meter  will  automatically  sense  a  stable reading  and  lock  the measurements,  the  HOLD  icon 
appears on the display. If disabled, press the    key, the meter will immediately lock the displayed value. Press the 

Meas

 key to resume measuring. 

 

 

 
 
 
 
 
 

Summary of Contents for Bante520

















Reviews: