Banner DF-G3 Long Range Expert Instruction Manual Download Page 28

Page: 28 / 36

Required Overcurrent

Protection

WARNING: Electrical

connections

must be made by

qualified

personnel in accordance with local and

national

electrical codes and

regulations.

Overcurrent

protection

is required to be provided by end product

application

per the supplied table.

Overcurrent

protection

may be provided with external fusing or via Current

Limiting,

Class 2 Power Supply.

Supply wiring leads < 24 AWG shall not be spliced.

For

additional

product support, go to

http://www.bannerengineering.com

Supply Wiring (AWG)

Required Overcurrent

Protection

(Amps)

5.0

3.0

2.0

1.0

0.8

0.5

Certifications

Industrial
Control
Equipment

3TJJ

Class 2 power

4.1 Excess Gain Curves

100

1000

10000

0.1

100

1000

Distance (mm)

24mS

8mS

1&2mS

500uS

Figure 13.

Diffuse—PBT16U

100

1000

10000

100000

0.1

100

1000

Distance (mm)

24mS

8mS

1&2mS

500uS

Figure 14.

Diffuse—PBT26U

DF-G3 Long Range Expert

™

Dual Display Fiber

Amplifier

www.bannerengineering.com - Tel: 763.544.3164

Summary of Contents for DF-G3 Long Range Expert




































Search results

Summary of Contents for DF-G3 Long Range Expert

Reviews:

Banner DF-G3 Long Range Expert, Instruction Manual, Page: 28 / 36

Search results

Summary of Contents for DF-G3 Long Range Expert

Reviews: