Banner DF-G3 Long Range Expert Instruction Manual Download Page 22

Page: 22 / 36

Method

Action

Result

SET

Button

•

Present sensing

condition

•

Click the SET rocker

button

Threshold

Condition

Accepted Displays

read "Lt SEt" then alternate "PASS" with %

Offset

16; Sensor returns to Adjust mode

Threshold

Condition

Not Accepted

Displays read "Lt SEt" then alternate "FAIL"

with minimum %

Offset

16 for sensing

condition;

Sensor returns to Adjust mode

Remote Input

•

Present sensing

condition

•

Single-pulse the remote input

3. Return to RUN Mode

Method

Action

Result

SET

Button

Move Mode switch to RUN

Display: Red - Signal Level; Green -

Threshold

Remote Input

action

required; sensor returns to RUN

mode

automatically

3.5.5 Dark SET

• Sets a threshold a programmable %

offset

above the presented

condition

• Any

condition

lighter than the threshold

condition

causes the output to change state

• Threshold can be adjusted using "+" and "-" rocker

button

(Manual Adjust)

• Recommended for

applications

where only one

condition

is known, for example a stable dark background with varying lighter

targets

• See Program Mode for programming the

Offset

Percent

setting

Note:

Offset

Percent MUST be programmed to Minimum

Offset

to accept

conditions

of no signal (0 counts).

A single sensing

condition

is presented, and the sensor

positions

a threshold a programmable %

offset

above the presented

condition.

When a

condition

lighter than the threshold is sensed, the output either turns ON or OFF, depending on the LO/DO

setting.

Sensor positions

threshold a programmable

% offset above the

presented condition

Threshold position

adjusted by

Manual Adjust

Darkest

(no signal)

Most Light

(saturated

signal)

Output OFF

Output ON

Condition

Presented

Figure 11. Dark SET (Light Operate shown)

Dark SET and Manual Adjust

Moves switching threshold value up or down to make adjustments

• Slide Mode switch to ADJ to enter Adjust mode

• Press "+" to increase; press "-" to decrease

◦

GREEN display shows the switching threshold value

◦

2 seconds

after

adjustment, the GREEN display will

flash

times

confirm

• Slide Mode switch to RUN to complete

operation

16 See

Troubleshooting

on page 25 for more

explanation

of the %

Offset

displayed

after

the Light SET method

DF-G3 Long Range Expert

™

Dual Display Fiber

Amplifier

www.bannerengineering.com - Tel: 763.544.3164

Summary of Contents for DF-G3 Long Range Expert




































Search results

Summary of Contents for DF-G3 Long Range Expert

Reviews:

Banner DF-G3 Long Range Expert, Instruction Manual, Page: 22 / 36

Search results

Summary of Contents for DF-G3 Long Range Expert

Reviews: