Banner DF-G3 Long Range Expert Instruction Manual Download Page 24

Page: 24 / 36

Sensor positions

threshold exactly at

the presented condition

Threshold position

adjusted by

Manual Adjust

Darkest

(no signal)

Most Light

(saturated

signal)

Output OFF

Output ON

Condition

Presented

Figure 12.

Calibration

SET (Light Operate shown)

Calibration

SET and Manual Adjust

Moves switching threshold value up or down to make adjustments

• Slide Mode switch to ADJ to enter Adjust mode

• Press "+" to increase; press "-" to decrease

◦

GREEN display shows the switching threshold value

◦

2 seconds

after

adjustment, the GREEN display will

flash

times

confirm

• Slide Mode switch to RUN to complete

operation

Remember: Auto Thresholding is

automatically

disabled in

Calibration

SET

Follow these steps to perform a

Calibration

SET:

Note: TEACH

Selection

must be programmed to CAL SEt.

1. Enter Adjust Mode

Method

Action

Result

SET

Button

•

Set Mode switch to ADJ

Display: Red - Signal Level; Green -

Threshold

Remote Input 21

action

required; sensor is ready for

Calibration

SET method

2. SET Sensing

Condition

Method

Action

Result

SET

Button

•

Present sensing

condition

•

Click the SET rocker

button

Threshold

Condition

Accepted Displays

read "cAL SEt" then

flashes

"PASS"; Sensor

returns to Adjust mode

Threshold

Condition

Unacceptable

Displays read "cAL SEt" then

flashes

"FAIL";

Sensor returns to Adjust mode

Remote Input

•

Present sensing

condition

•

Single-pulse the remote input

3. Return to RUN Mode

20 SET

Button:

0.04 seconds

≤

"Click"

≤

0.8 seconds

21 Remote Input: 0.04 seconds

≤

0.8 seconds

DF-G3 Long Range Expert

™

Dual Display Fiber

Amplifier

www.bannerengineering.com - Tel: 763.544.3164

Summary of Contents for DF-G3 Long Range Expert




































Search results

Summary of Contents for DF-G3 Long Range Expert

Reviews:

Banner DF-G3 Long Range Expert, Instruction Manual, Page: 24 / 36

Search results

Summary of Contents for DF-G3 Long Range Expert

Reviews: