B&R PROVIT 4000, User Manual

Page: 54 / 100

5 4
CAN Disable open
1)
CAN Controller activated (I/O addresses see section "5.1 B&R I/O Area")
inserted CAN Controller deactivated (I/O area free for e.g. ISA cards)
IRQ10 open IRQ10 available for ISA cards
inserted
1)
IRQ10 used for CAN Controller
COM1 Disable open
1)
COM UART activated (I/O addresses see section "6.1.2 I/O Address Assignments")
inserted COM UART deactivated (I/O area free for e.g. ISA cards)
IRQ4 open IRQ4 not used for COM1, that means this IRQ resource is available for other uses (other COMs or ISA cards)
inserted
1)
IRQ4 used for COM1
IRQ11 open 1) IRQ11 not used fro COM1, that means this IRQ resource is available for other uses (other COMs or ISA cards)
inserted IRQ11 used for COM1
COM2 Disable open 1) COM UART activated (I/O addresses see section 6.1.2 I/O Address Assignment")
inserted COM UART deactivated (I/O area free for e.g. ISA cards)
IRQ3 open IRQ3 not used for COM2, that means this IRQ resource is available for other uses (other COMs or ISA cards)
inserted 1) IRQ3 used for COM2
IRQ12 open 1) IRQ12 not used for COM2, that means this IRQ resource is available for other uses (other COMs or ISA cards)
inserted IRQ12 used for COM2
COM3 Disable open 1) COM UART activated (I/O addresses see section "6.1.2 I/O Address Assignments")
inserted COM UART deactivated (I/O area free for e.g. ISA cards)
IRQ4 open 1) IRQ4 not used for COM3, that means this IRQ resource is available for other uses (other COMs or ISA cards)
inserted IRQ4 used for COM3
IRQ11 open IRQ11 not used for COM3, that means this IRQ resource is available for other uses (other COMs or ISA cards)
inserted 1) IRQ11 used fro COM3
COM4 Disable open 1) COM UART activated (I/O addresses see section "6.1.2 I/O Address Assignment")
inserted COM UART deactivated (I/O area free for e.g. ISA cards)
IRQ3 open 1) IRQ3 not used for COM4, that means this IRQ resource is available for other uses (other COMs or ISA cards)
inserted IRQ3 used for COM4
IRQ12 open IRQ12 not used for COM4, that means, that means this IRQ resource is available for other uses (other COMs or ISA cards)
inserted 1) IRQ12 used for COM4
LPT Disable LPT1 open 1) LPT1 is activated (I/O addresses see section "6.1.2 I/O Address Assignment")
(parallel interface) inserted LPT1 is deactivated (I/O area free for e.g. ISA cards)
IRQ7 (LPT1) open IRQ7 not used LPT1, that means this IRQ resource is available for other uses (ISA cards)
inserted 1) IRQ7 used for LPT1
ITR Disable open 1) The built-in INTERACT hardware key is operated via the internal LPT2 which is not available for the user
inserted The built-in INTERACT hardware key is deactivated, that means the I/O addresses 278 - 27F are available for other uses (ISA cards)
Front Without Display open 1) Both jumpers open: Display operates with built-in display
inserted Both jumpers inserted: Device operates without built-in display
FDD Disable open
1)
Disk drive is activated (I/O addresses see section "6.1.2 I/O Address Assignments")
inserted Disk drive is deactivated (I/O area free for e.g. ISA cards)
HDD Disable open
1)
Hard disk is activated (I/O addresses see section "6.1.2 I/O Address Assignments")
inserted Hard disk is deactivated (I/O area free for e.g. ISA cards)
VGA Standby open
1)
VGA is activated (I/O addresses see section "6.1.2 I/O Address Assignments")
inserted VGA is in Standby Mode. A VGA Controller may not be inserted in the same address area
1) ... Default Setting