background image

10 

 

THE HEAD/LIFT PAGE HAS TO BE ENABLED IN THE SET UP MENU before 
it can be displayed. 
 

The port and starboard tacks are stored manually as 

PORT

 and 

STBD

 

headings (see SETTING THE COURSE MEMORIES). When the helmsman 
has to vary from these headings due to wind changes the legends 

HEAD

 or 

LIFT

 will appear on the display for the relevant tack. If wind data is available 

over the Network a tack will automatically change between the 

PORT

 and 

STBD

 reference course. Otherwise it can be switched manually by two short 

presses of the 

LOCK

 key or the remote button. The 

HEAD/LIFT

 values are 

displayed in the analogue bar graph as degrees.  If the Off Course alarm is 
enabled the unit will sound an alarm and 

HEAD

 will flash if a head occurs, 

pressing 

ENTER

 on the unit will cancel the alarm. The alarm will not sound for 

a lift. 

THE HEAD/LIFT DISPLAY

 

MODE

TIMER

LOCK

SETUP

LIGHTS

ENTER

Network COMPASS

LIFT

30

20

10

30

20

10

PORT

MODE

TIMER

LOCK

SETUP

LIGHTS

ENTER

Network COMPASS

LIFT

30

20

10

30

20

10

STBD

MODE

TIMER

LOCK

SETUP

LIGHTS

ENTER

Network COMPASS

HEAD

30

20

10

30

20

10

STBD

MODE

TIMER

LOCK

SETUP

LIGHTS

ENTER

Network COMPASS

HEAD

30

20

10

30

20

10

PORT

Summary of Contents for Network Compass


























Reviews: