background image

13

PanelMax

 installation instructions

16. Home Owner Safety Warnings!

WARNING! IMPORTANT SAFETY INSTRUCTIONS 

IT IS IMPORTANT FOR THE SAFETY OF PERSONS TO FOLLOW ALL INSTRUCTIONS.  

SAVE THESE INSTRUCTIONS

This automatic garage door opener is designed and tested to offer safe service provided it is installed and 

operated in strict accordance with the following safety warnings. Failure to comply with the following instructions 

may result in death, serious personal injury or property damage.

 

WARNING!

•  Automatic Door - the door may operate unexpectedly, therefore do not allow anything 

to stay in the path of the door.

•  Details on how to use manual release. When operating the manual release while the 

door is open, the door may fall rapidly due to weak or broken springs, or due to being 

improperly balanced. 

•  DO NOT disengage the opener to manual operation with children/persons or any 

objects including motor vehicles within the doorway.

•  If the door is closing and does not re-open when obstructed, discontinue use. DO NOT 

use a door with faulty obstruction sensing.

•  Frequently examine the installation, in particular check cables, springs and mountings 

for signs of wear, damage or imbalance. DO NOT use if repair or adjustment is needed 

since fault in the installation or an incorrectly balanced door may cause injury..

ELECTROCUTION!

•  Place opener in protected area so that it does not get wet.

•  DO NOT spray with water .

•  DO NOT open the protective covers.

•  DO NOT operate opener if cable is damaged. It must be replaced by the manufacturer, 

its service agent or similarly qualified person in order to avoid a hazard.

•  Disconnect the supply(s) when cleaning or other maintenance is being carried out..

DO NOT DO IT  

YOURSELF

•    

Keep the garage door balanced. Sticking or binding doors must be repaired. Garage 

doors, door springs, brackets and their hardware are under extreme tension and can 

cause serious personal injury. 

DO NOT

 attempt any garage door adjustment. 

DO NOT

 

use if repair or adjustment is needed. Call for a professional garage door service.

 CAUTION:

 

Emergency access

•  If your garage has no pedestrian entrance door, an emergency access device should  

be installed. This accessory allows manual operation of the garage door from outside 

in case of power failure.

Entrapment under  

operating door  

•  Watch the moving door and keep people away until the door is completely opened 

or closed. DO NOT operate door when persons are near the door.

•  DO NOT allow children to play with door controls or transmitters. Keep remote controls 

away form children.

•  The appliance is not to be used by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they have 

been given supervision or instruction.

•  Children being supervised not to play with the appliance.

•  Regularly conduct Open and Close cycle testing.

•  Each month check that the drive reverses when the door contacts a 40mm high object 

placed on the floor. Adjust if necessary and recheck since an incorrect adjustment may 

present a hazard.

•  Ensure the garage door is in good working order by undertaking regular servicing.

•  Wall transmitters should be installed in a location where the garage door is visible, but 

out of the reach of children at a height of at least 1.5m.

•  Install Safety Beams (recommended).

Fall from Ladder

•  Ensure ladder is the correct type for the job.

•  Ensure ladder is on flat ground.

•  Ensure user has 3 points of contact while on ladder.

Entanglement in or 

laceration from  

moving door

•  Keep hands and loose clothing clear of door and guides at all times.

•  Keep hands clear of moving door as sharp edges can cause cuts or lacerations.

DIY

Summary of Contents for PanelMax SDO-8
























Reviews: