B&D Controll-A-Door Advance Instruction Manual Download Page 21

Page: 21 / 24

Controll-A-Door

S & PanelPro

Instruction Manual

25. Service Schedule

B&D Doors is a division of B&D Australia Pty Ltd
Phone: 13 62 63
Website: www.bnd.com.au

Year /

Approx. Cycles

Date

Details

1 / 3,000

2 / 6,000

3 / 9,000

4 / 12,000

5 / 15,000

Service Indicator (Only Available with CAD S)

While the door opener does not require regular
servicing, to function correctly the door must be
in good operating condition. As a reminder the

Controll-A-Door

S has a built in maintenance

counter. This counter has a factory default of 3000
cycles, which is the recommended service interval.

AUX /

OSC

SB-2

SB-1

When this counter expires the yellow SERVICE LED will light up and opener beep three times at the start of each cycle

In addition the courtesy light will flash and opener beep five times at the end of open cycle (when the door is fully open).

These warning signals will self extinguish after 30 cycles.

When this service counter is triggered it is strongly recommended you

contact your garage door dealer to arrange a door service

See above for Recommended Service Schedule.

However, if you choose not to have your door serviced the counter can be reset simply by pressing the SET button.

Recommended Service Schedule

Summary of Contents for Controll-A-Door Advance

























Search results

Summary of Contents for Controll-A-Door Advance

Reviews:

Related manuals for Controll-A-Door Advance

Brands by name

Popular brands

B&D Controll-A-Door Advance, Instruction Manual

Search results

Summary of Contents for Controll-A-Door Advance

Reviews:

Related manuals for Controll-A-Door Advance

Brands by name

Popular brands