B&B Electronics e-Linx EIRP610-2SFP-T User Manual Download Page 16

Page: 16 / 147

Hardware Description

2.4 LED Indicators

LED

Color

Status

Meaning

PWR

Green

The switch is powered on

Off

No power

R.M.

Green

The switch is the master of the X-Ring

Off

The switch is not the master of the X-Ring

PWR1

Green

Power 1 is active

Off

Power 1 is inactive

PWR2

Green

Power 2 is active

Off

Power 2 is inactive

FAULT

Red

Power or port failure

Off

No failure, or no power applied

P9, P10

(RJ-45)

Green (Upper

LED)

A network device is detected.

Blinking

The port is transmitting or receiving data.

Off

No device attached

Green (Lower

LED)

1000M

Off

10/100M

Link/Active

(P9, P10 SFP)

Green

The SFP port is linking

Blinks

The port is transmitting or receiving data.

Off

No device attached

P1 to P8

Green

A network device is detected.

Manual Documentation Number EIRP610-2SFP-T

– 0912m

www.bb-elec.com

www.bb-europe.com

Summary of Contents for e-Linx EIRP610-2SFP-T




















































































































































Search results

Summary of Contents for e-Linx EIRP610-2SFP-T

Reviews:

Related manuals for e-Linx EIRP610-2SFP-T

Brands by name

Popular brands

B&B Electronics e-Linx EIRP610-2SFP-T, User Manual

Search results

Summary of Contents for e-Linx EIRP610-2SFP-T

Reviews:

Related manuals for e-Linx EIRP610-2SFP-T

Brands by name

Popular brands