B&B Electronics e-Linx EIRP610-2SFP-T User Manual Download Page 82

Page: 82 / 147

Web-Based Management

6.18.2 802.1Q VLAN

Virtual Local Area Network (VLAN) can be implemented on the switch to logically create

different broadcast domains.

When the 802.1Q VLAN function is enabled, all ports on the switch belong to default

VLAN of VID 1, which means they logically are regarded as members of the same

broadcast domain. The valid VLAN ID is in the range of numbers between 1 and 4094. The

limit of VLAN groups is up to 256 including the default VLAN that cannot be deleted.

Each member port of 802.1Q is on either an Access Link (VLAN-tagged) or a Trunk Link

(no VLAN-tagged). All frames on an Access Link carry no VLAN identification.

Conversely, all frames on a Trunk Link are VLAN-tagged. A third mode (Hybrid) exists. A

Hybrid Link can carry both VLAN-tagged frames and untagged frames. A single port is

supposed to belong to one VLAN group, except when it is on a Trunk/Hybrid Link.

The technique of 802.1Q tagging inserts a 4-byte tag, including VLAN ID of the destination

port—PVID, in the frame. With the combination of Access/Trunk/Hybrid Links,

communication across switches can also be sent through tagged and untagged ports.

802.1Q Configuration



Pull down the selection item and focus on

802.1Q

then press

Apply

to set the

VLAN Operation Mode in

802.1Q

mode.



Enable GVRP Protocol:

GVRP (GARP VLAN Registration Protocol) is a protocol

that facilitates control of virtual local area networks (VLANs) within a larger network.

GVRP conforms to the IEEE 802.1Q specification, which defines a method of tagging

frames with VLAN configuration data. This allows network devices to dynamically

exchange VLAN configuration information with other devices. For example, having

enabled GVRP on two switches, they are able to automatically exchange the

information of their VLAN database. Therefore, the user doesn‘t need to manually

configure whether the link is trunk or hybrid, the packets belonging to the same VLAN

can communicate across switches. Tick this checkbox to enable GVRP protocol. This

Manual Documentation Number EIRP610-2SFP-T

– 0912m

www.bb-elec.com

www.bb-europe.com

Summary of Contents for e-Linx EIRP610-2SFP-T




















































































































































Search results

Summary of Contents for e-Linx EIRP610-2SFP-T

Reviews:

Related manuals for e-Linx EIRP610-2SFP-T

Brands by name

Popular brands

B&B Electronics e-Linx EIRP610-2SFP-T, User Manual

Search results

Summary of Contents for e-Linx EIRP610-2SFP-T

Reviews:

Related manuals for e-Linx EIRP610-2SFP-T

Brands by name

Popular brands