background image

37 / 96

0006081053_200801

E

N
G

L

I

S

H

The three-phase power supply line must have a switch with fuses. 
The  regulations  further  require  a  switch  on  the  burner’s  power 
supply line, outside the boiler room and in an easily accessed po

-

sition. For the electrical connections (line and thermostats), follow 
the wiring diagram enclosed. To carry out the connection of the 
burner to the power supply line proceed as follows:

1)  Remove  the  lid  by  unscrewing  the  4  screws  (1)  in  figure  1, 

without removing the transparent door. In this way the burner’s 

electrical panel can be accessed. . 

2)  Slacken le screws (2) and, after removing the cable float (3), 

pass the two 7 and 4 pole plugs through the hole (see figure  

2). Connect  the power supply cables (4) to the contactor, connect 

the cable to ground (5) and close the cable holder. 

3)  Reposition the cable float as in figure 3. Turn the cam (6) so 

that the float exerts sufficient pressure on the two cables, then 
tightethe screws that fasten the cable float. Finally, connect the 
two 7 and 4-pole plugs.

 

IMPORTANT: the housings for the cables for the 7 and 4-pole 

plugs are provide respectively for cable 

Ö  9.5÷10  mm  and  Ö  8.5÷9  mm,  this  to  make  sure  the 

protection rating is IP 54 (standard IEC EN60529) for the 
electrical panel.

4)  o reclose the electrical panel lid, tighten  the 4 screws (1) with 

a torque of about 5 Nm to ensure the correct seal. At this point 
to be able to access the control panel (8), unfasten the tran-

sparent door (7), using slight touch pressure in the direction of 
the arrows in figure 4, move it the short distance to separate it 

from the lid.

5)  to properly resecure the transparent door  on the panel proceed 

as indicated in  5:position the hooks at their hooking points and 
(9) slide the door in the direction indicated by the arrow until it  
clicks. It is now well sealed.

ELECTRICAL CONNECTIONS

Important: only qualified technicians may open the burner’s 
electrical panel.

Figura 1

Figura 2

Figura 3

Figura 4

Figura 5

Summary of Contents for TBL 105P
































Reviews: