33 / 81
0006080098_200302
FASTENING THE BURNER TO THE BOILER
The burner must be applied to the boiler’s iron plate, where the stud bolts given as standard accessories have been
already fitted in accordance with the plate drilling. It is advisable to electrically weld the stud bolts to the internal part
of the plate to avoid extracting them together with the unit’s locking nuts, should the burner be disassembled.
If the plate is not supplied with heat insulation, it is necessary insert an insulating protection at least 10 mm. thick
between the plate and the boiler. To fit the insulating flange between the burner and the boiler plate, remove the
end section of the combustion head.
Ensure that the combustion head enters the furnace to the extent specified by the boiler manufacturer.
(The flange used to fasten the burner to the boiler can be moved along the combustion head in order to allow the
combustion head to enter the furnace to the extent required for the different types of boiler).
When this operation has been carried out, connect the burner to the light oil pipeline, as illustrated in our drawings.
The burner can be supplied with a normal head or a long head on request.
ENGLISH
ELECTRICAL CONNECTIONS
It is advisable to make all connections with flexible electric
wire.
The electric lines should be at an adequate distance from
hot parts.
Make sure that the electric line to which the unit will be
connected has frequency and voltage ratings suitable for
the burner. Check that the main line, the relevant switch
with fuses (essential) and the current limiter (if required)
are capable of withstanding the maximum current absorbed
by the burner.
For details, refer to the specific electric diagram for each
single burner.
FUEL FEED SYSTEM (LIGHT OIL)
The burner pump should receive fuel from a feed circuit which has an ancillary pump and, in some cases, a pres-
sure regulator capable of modifying the pressure value 0,2 to 1 bar (see drawing BT 8575/1).
In this case, the value of the fuel feed pressure at the burner pump (0,2 ÷ 1 bar) should not vary when the burner
is at a standstill or when it is operating at the maximum fuel delivery required by the boiler.
Normally it is possible to realize a circuit without a pressure regulator as shown in drawing n° BT 8666/3.
The feed circuit must be realized according to drawing BT 8575/1 or to drawing BT 8666/3.
The dimension of the pipelines should be in function with their length and with the output of the pump utilized.
Our instructions cover the basic requirements needed to ensure efficient operations. All rules and regulations exi-
sting in the country of installation should be strictly complied with and the local fire brigade should be consulted.
MOUNTING INSTRUCTIONS FOR ADJUSTA-
BLE STAND
- Insert theadjustable stand in the hole located in
the bottom part of the burner case as shown in
the sketch 0002934500.
Summary of Contents for GI 350 DSPG
