baltur BPM 35 SM, Maintenance, Use And Installation Manual

Page: 5 / 22

3 / 18
0006081359_200906
ENGLISH
GENERAL INSTRUCTIONS
This booklet constitutes an integral and essential part of the product
and should be supplied to the installer. Read the instructions
contained in this booklet carefully as they give important directions
regarding the safety of installation, use and maintenance. Preserve
this booklet with care for any further consultation.
The installation of the burner must be carried out in compliance with
current regulations, according to the instructions of the manufacturer
and by qualified personnel. An incorrect installation can cause
injury or damage to persons, animals and objects, for which the
manufacturer cannot be held responsible.
This appliance should only be used for the purpose it has been
designed for. Any other use is to be considered improper and
therefore dangerous. The manufacturer cannot be considered
responsible for any damages caused by improper, erroneous or
unreasonable use.
Before carrying out any cleaning or maintenance operation,
disconnect the appliance from the power supply, by using the main
system switch or through the appropriate interception devices.
In case of failure and/or malfunctioning, switch off the equipment
and refrain from trying any repair or direct intervention. Call in
qualified personnel only. Any repair must be carried out by a servicing
centre authorised by the manufacturing firm, one using original
replacements exclusively. Non-observance of the above could
compromise the safety of the appliance. In order to guarantee the
efficiency of the appliance and its proper operation it is indispensible
to keep to the manufacturer’s directions, by ensuring the periodical
servicing of the appliance is carried out by professionally qualified
personnel.
As soon as one decides not to use the appliance further, one should
take care to render innocuous those parts liable to be potential
sources of danger.
The transformation from a gas (natural gas or liquid gas) to a gas of
another group must be made exclusively by qualified personnel.
Before starting up the burner for the first time ask qualified personnel
to check:
a) that the data on the information plate corresponds to that
required by the gas, and electrical supply networks;
b) that the calibration of the burner is compatible with the
boiler output;
c) that the comburent air flow and the fumes evacuation take
place properly in accordance with the regulations in force;
d) that correct aeration and maintenance are possible.
After each reopening of the gas cock wait a few minutes before
restarting the burner.
Before carrying out whatever intervention which foresees the
dismantling of the burner or the opening of any of the accesses
for inspection, disconnect the electrical current and close off the
gas cocks.
Do not deposit containers of inflammable substances in the location
where the burner is situated.
On noticing the smell of gas do not touch any electrical switch.
Open all doors and windows. Shut off the gas cocks. Call qualified
personnel.
The room where the burner is located must have the openings
required by local regulations in force. Should you have any doubts as
to the circulation of the air in the room, then you should first measure
the CO
2
value with the burner working at its maximum delivery and
with the room ventilated solely by means of the openings that feed
air to the burner; a second CO
2
measurment should then be taken
with the door open. The CO
2
value should not vary very much from
the first to the second reading. Should there be more than one burner
and one fan in the same room, then this test must be carried out
with all the appliances working at the same time.
Never cover up the burner room’s air vents, the burner’s fan’s
air-intake openings or any existing air ducts or air gratings, thus
avoiding:
- the formation of poisonous/explosive mixtures of gases in the
burner room;
- combustion with insufficient air, which would be dangerous, costly
and cause pollution.
The burner must at all times be protected from rain, snow and
freezing.
The room where the burner is housed should be kept clean at all
times, and there should be no volatile substances in the vicinity,
substances which could be sucked into the fan and could block up
the internal ducts of the burner.
The burner must be fed with the type of fuel for which it was designed,
as indicated on the data plate and in the technical characteristics
given in this manual. The fuel feed line must be sealed and must
be of the rigid variety, with an interposed metal expansion bend
with either a flange joint or a threaded joint. Furthermore, the feed
line must be equipped with all the adjustment and safety devices
required by the local regulations in force. Particularly ensure that no
foreign bodies get into the feed line during installation.
Ensure that the electrical power supply used conforms to the
technical characteristics indicated on the data plate and in this
manual. The burner must be connected to an effective system
earthed in accordance with the current regulations. Should there be
any doubts, the verification should be made by qualified persons.
Never exchange neutral and phase wires.
The burner can be connected up to the mains supply using a plug
connection only if the latter is of the kind that does not allow neutral
and phase wires to be reversed. Install a main switch for the heating
system on the control panel, as required by current regulations.
The entire electrical system, and in particular cable cross-sections,
should conform to the maximum absorbed capacity indicated on the
appliance data plate and in this manual.
Should the burner’s mains cable be found faulty, it must only be
replaced by qualified persons.
Do not touch the burner with parts of the body which are wet or
when in bare feet.
Do not pull (stretch) the mains cables and keep them well away
from heat sources.
The electrical connections must be made exclusively by qualified
experts and the relative regulations in force must be scrupulously
applied.
After removing the packaging materials, check the content integrity
and make sure that no damages have occured during transportation.
In case of doubt, do not use the burner and contact the supplier.
The packaging material (wooden cages, cartons, plastic bags, foam,
clips, etc...) are potential sources of pollution and danger, if left lying
around; they should be collected up and disposed of in the correct
way (in a suitable place).