background image

8

Install Dash Lamp

The Max Charge Dash Lamp (#17) terminal provides the ability to activate a visual or 

audible indicator when the regulator monitors the following conditions: Low system 

voltage, high system voltage, high alternator temperature, high battery temperature 

(temperature conditions are only indicated when appropriate temperature sensors are 

connected) and no voltage on stator, indicating that the alternator has failed. When 

a described condition is detected, the regulator sends the Dash Lamp terminal from 

neutral to ground. To utilize the Dash Lamp function:

1. 

Connect a small LED or incandescent lamp, or an   (piezo) alert 

(maximum current 

flow is 500 mA) to a positive voltage source.

2. 

Connect the negative terminal on the lamp or audible alert to the Dash 

Lamp 

terminal on the regulator.

3. 

When connected, the lamp should flash at regulator start-up to indicate  

active status. 

Install SmartLink™ Adapter

If you wish to connect the MC-618 to a SmartLink™ network, this is done via the SmartLink™ Adapter, part # SG2-0404 It is 

included in the MC-618H kit, but not if you purchased the regulator without a harness. The two fast-on connectors shown here to 

the left are connected to pin 10 and 11 on the regulator.  Of the two Deutsch-style connectors on the right side, only one is used 

in a single MC-618 installation. In all instances, it is connected to an existing SmartLink™ device using a SmartLink™ cable 

(SG2-0400, not included) between that device and the adapter.

NOTE: 

For more SmartLink™ installation instructions, see the SG200 Manual

NOTE: 

A Color Display CANNOT be plugged directly into the SmartLink™  adapter cable without a SmartShunt on 

the network. The SmartShunt is needed to power the Network. The display will not function without this power.

 

17

16

15

14

12

13

10

11

9

7

6

5

8

4

3

2

1

 

17

16

15

14

12

13

10

11

9

7

6

5

8

4

3

2

1

11

10

10

10

11

10

Connect any SmartLink™ device 

here

 

17

16

15

14

12

13

10

11

9

7

6

5

8

4

3

2

1

11

10

Dual Engines/Regulators 

Requires Centerfielder II, not 

shown 

Single Engine/Regulator

Connect any SmartLink™ device 

here

Magnetic

Reed Switch

17
16

15

14

13

12

11

10

9

8

7

6

5

1

2

3

4

NOTE

: When Two regulators are used on a single SmartLink™ Network, the Device ID of one regulator MUST be set 

to “B” See the basic programming section entitled “Programming the SmartLink™ Device ID” for more information

SmartLink™ Cable

SG2-0400 10M

SG2-0403  5M

Summary of Contents for Max Charge MC-618



























Reviews: