Section
3–12
MN1229
Optional Control Signal Wiring
Continued
Control Inputs (Optional)
These control inputs are optional. Their reference (common) is CREF at X3-7
(see Figure 3-3). The voltage range is +12VDC to +29VDC for these inputs.
They may be used by a PLC or other signal source within your application.
1.
Connect the Machine Input 1 (MA
I
1) signal to X3-16.
2.
Connect the Machine Input 2 (MA
I
2) signal to X3-17.
These inputs are galvanically isolated. Their reference (common) is CGND at
X3-8 of Figure 3-3.
3.
Connect the Pulse Input signal to X3-14.
4.
Connect the Direction Input signal to X3-15.
Control Outputs (Optional)
Four Opto Isolated outputs are available for “Active Low” (Sink) use.
Connect one or more of the control outputs as follows: (see in Figure 3-9).
1.
Connect the Ground Return of the power source to X3-8.
2.
Connect a customer pr24VDC source (range = +12VDC to
+29VDC) to X3-6 the CIV input (Customer Input Voltage).
3.
Connect Machine Output 1 (MAO1) X3-18 to PLC.
4.
Connect Machine Output 2 (MAO2) X3-19 to PLC.
5.
Connect the Drive OK load to X3-20.
Figure 3-9 Optional Control Outputs
Machine Output 1
Machine Output 2
Drive OK
6
18
X3
19
20
8
To Customer
Provided PLC
Ground Return
CIV *
*
24VDC nominal at 100mA minimum.
Note:
These outputs are programmable. Refer to software setup manual for
further details.
Optional Control Signal Wiring Continued
Control Inputs (Optional)
These control inputs are optional. Their reference (common) is CREF at X3-7
(see Figure 3-3). The voltage range is +12VDC to +29VDC for these inputs.
They may be used by a PLC or other signal source within your application.
1. C o n n e c t the Machine Input 1 (MAI1) signal to X3-16.
2. C o n n e c t the Machine Input 2 (MAI2) signal to X3-17.
These inputs are galvanically isolated. Their reference (common) is CGND at
X3-8 of Figure 3-3.
3. C o n n e c t the Pulse Input signal to X3-14.
4. C o n n e c t the Direction Input signal to X3-15.
Control Outputs (Optional)
Four Opto Isolated outputs are available for "Active Low" (Sink) use.
Connect one or more of the control outputs as follows: (see in Figure 3-9).
1. C o n n e c t the Ground Return of the power source to X3-8.
2. C o n n e c t a customer pr24VDC source (range = +12VDC to
+29VDC) to X3-6 the CIV input (Customer Input Voltage).
3. C o n n e c t Machine Output 1 (MAO1) X3-18 to PLC.
4. C o n n e c t Machine Output 2 (MAO2) X3-19 to PLC.
5. C o n n e c t the Drive OK load to X3-20.
Figure 3-9 Optional Control Outputs
X3
Ground Return
8
CIV .>
Machine Output 1
Machine Output 2
Drive OK
6
18
19
20
To Customer
Provided PLC
* 24VDC nominal at 100mA minimum.
Note: T h e s e outputs are programmable. Refer to software setup manual for
further details.
3-12
M
N
1
2
2
9
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
