Balboa Clim8zone Installation Manual Download Page 3

TM                        

INSTALLATION GUIDE   

     

42391 Rev 

A

Balboa Water Group   |   Your Single Source Solution

5

4

ATTENTION

■ This manual includes all the 

necessary information about the 

use and the installation of the 

CLIM8ZONE unit.
■ The installer follow the installation 

instructions contained in the guide. 

Improper installation will void the 

warranty.
■ The manufacturer declines any 

responsibility for the damage caused 

by people, objects and errors due to 

the installation against the manual. 

Any use that isn’t in accordance with 

the origin of its manufacturing will be 

regarded as dangerous.

WARNING

■ Do not use means to accelerate the 

defrosting process, other than those 

recommended by the manufacturer.

■ The appliance shall be stored in a 

room without continuously operating 

ignition sources (for example: open 

flames, an operating gas appliance or 

an operating electric heater.)
■ Do not pierce or burn.
■ Be aware that refrigerants may not 

contain an odor.
■ The CLIM8ZONE unit shall be 

installed, operated and stored in an 

open room larger than 3 m³.
■ Note the manufacturer may provide 

other suitable examples or may 

provide additional information about 

the refrigerant odor.

WARNING

■ If you power Off the CLIM8ZONE 

unit, please empty the water in heat 

pump always during winter time or 

when the ambient temperature drops 

below 0°C, or else the titanium heat 

exchanger will be damaged because 

of being frozen, in such case, your 

warranty will be lost.

WARNING

WARNING

■ Please always cut the power supply 

if you want to open the cabinet 

to reach inside the CLIM8ZONE 

unit, because there is high voltage 

electricity inside.

WARNING

■ Please keep the display controller 

in a dry area, or close the insulation 

cover to protect the display controller 

from being damaged by humidity.

WARNING

■ Installation must be performed in 

accordance with the NEC/CEC and 

local code by authorized person only.

WARNING

■ Make sure the switch is turned 

to the power off position before 

installing the CLIM8ZONE unit or 

maintenance the heat pump.

WARNING

■ This appliance is not intended for 

use by persons (including children) 

with reduced physical, sensory 

or mental capabilities, or lack of 

experience and knowledge, unless 

they have been given supervision 

or instruction concerning use of the 

appliance by a person responsible for 

their safety.
■ Children should be supervised to 

ensure that they do not play with the 

appliance.

WARNING

■ Single wall heat exchanger, not 

suitable for potable water connection.

Summary of Contents for Clim8zone

















Reviews: