background image

Masoneilan Regulators Models 525 & 526 Manual  |  2

Copyright 2020 Baker Hughes Company. All rights reserved.

1. Introduction

The  following  instructions  should  be  thoroughly  reviewed 

and  understood  prior  to  installing,  operating  or  performing 

maintenance  on  this  equipment.  Throughout  the  text,  safety 

and/or caution notes will appear and must be strictly adhered to, 

otherwise, serious injury or equipment malfunction could result.

Serial Plate

The serial plate is usually fixed to the side of the actuator yoke. It 

indicates information about the regulator including size and type, 

pressure class rating, body/bonnet material, and serial number.

After Sales Service

Baker Hughes offers Masoneilan After Sales Service comprised 

of  highly  qualified  technicians  to  support  the  installation, 

operation, maintenance and repair of its equipment. For support 

contact the local Baker Hughes Masoneilan representative or 

Baker Hughes Masoneilan factory located closest to you.

Spare Parts

Only  Masoneilan  replacement  parts  should  be  used  when 

carrying out maintenance operations. Obtain replacement parts 

through local Masoneilan representatives or Masoneilan Parts 

Department.

When ordering spare parts, the MODEL AND SERIAL NUMBERS 

indicated on the manufacturer’s serial plate MUST BE GIVEN. 

The serial plate is on the side of the actuator yoke.

Actuator and Accessories

Actuators and other valve accessories have their own instruction 

manuals that provide information and details on the assembly 

and installation. Refer to the appropriate instruction manual for 

each unique accessory.

2. General

These  installation  and  maintenance  instructions  apply  to  all 

sizes and ratings of the Masoneilan 525/526 model regulators 

regardless of the type of trim used.
525/526 model double seat regulators are designed with built in 

versatility making them well-suited to handle a wide variety of 

process applications.

Standard construction offers a contoured plug with a threaded 

seat ring. The upper and lower plug guiding provides maximum 

support to ensure plug stability. A series of reduced area trim is 

available to provide wide flow range capabilities in all regulator 

sizes. Tight Shutoff Class II leakage is standard. 
Recommended spare parts required for maintenance are listed 

in  the  Parts  Reference  table  on  page  11. The  model  number, 

size,  rating  and  serial  number  of  the  valve  are  shown  on  the 

identification tag located on the actuator. Refer to the below chart 

for the 525/526 numbering system.

3. Unpacking

Care must be exercised when unpacking the regulator to prevent 

damage to the accessories and component parts. Should any 

problems arise, contact the local Masoneilan Representative or 

After Sales Department.

2nd

3rd

4th

1st

5.   Regulator 

Type

2.  Double 

Seat

5. Reducing Services

(1)

6.  Back Pressure 

Services

(2)

-50. Differential Pressure

-6. Extended Bonnet

Body Series

Plug Type

Other Options

(1) Downstream Pressure Controlled (See Figure 1a)
(2) Upstream Pressure Controlled (See Figure 1b)

Summary of Contents for Masoneilan 525 Seris

















Reviews: