Bailey pproach SE, Owner'S Manual

Page: 82 / 96

7-35
FITTED EQUIPMENT
Preparing for use (standard)
• Open the access door on the outside of
your motorhome.
• Remove the Waste Holding Tank by
pulling the safety catch (which holds the
tank in place) upwards.
• Pull the Waste Holding Tank outward to
the stop. Tip it slightly and take the tank
fully out.
• Place the tank upright and turn the
rotating emptying spout upwards. The
emptying spout ensures that the tank can
be easily and hygienically emptied.
• Remove the cap, with the measuring cup
inside, from the emptying spout and pour
the correct dosage of Thetford toilet fluid
(see product label) into the holding tank.
This avoids unpleasant smells and keeps
the inside of the tank clean. Next add
approximately 2 litres of water - enough to
ensure that the bottom of the Waste
Holding Tank is covered. Screw the cap
back onto the emptying spout and turn
back to its original position. The Emptying
Spout Measuring Cap is supplied inside
the toilet. Never add toilet fluid directly via
the blade or the toilet bowl as this could
damage the lip seal of the Waste Holding
Tank. Always pour the fluids via the
emptying spout. The lip seal is the water
tight seal around the top of the tank.
• Slide the Waste Holding Tank back into
its original position via the access door.
Make sure that it is secured with the
safety catch. Close the access door and
lock it. Your Thetford toilet is now ready
to use.
• Never use force if you cannot get the
tank back into pace easily. This may
cause serious damage. If blockage
occurs, always check that the blade
handle is in the correct position.
• For toilets with own Flush-Water Tank:
Open the water filling door and fill the
flush-water tank with the correct dosage
of Aqua Rinse. This Thetford toilet fluid
keeps the flush water fresh and improves
the flushing. Next, fill up the flush-water
tank with clean water (approximately 8
litres) using a watering can or hose. Your
toilet is now ready to use.
Using the toilet (standard)
• Turn the bowl to the desired position with
the lid closed and using both hands.
• To activate the control panel, press the
flush-button once. The control panel
display will stay activated for
approximately 5 minutes. Run some
water into the bowl by pressing the flush
button again briefly.
• The toilet may be used with the blade
open or closed. To open the blade, slide
the blade handle under the toilet bowl
sideways. After use, open the blade (if
still closed) and flush the toilet by
pressing the flush button for several
seconds (if necessary re-activate the
control panel). Close the blade after use.
If your toilet has its own flush-water tank,
please make sure that you do not travel
with a flush-water tank that is too full. Do
not travel with water in the toilet bowl.
Failure to adhere to this notice may result
in water damage to your motor home.
Emptying
The Waste Holding Tank has a capacity of 18
litres and required emptying when the red
light (LED) on the toilet control display lights
up. When the Waste Holding Tank only has
capacity for two more litres which is no more
than two to three further uses.
Make sure that the blade is closed. Open the
access door located outside the vehicle, pull
the safety catch upwards and remove the
Waste Holding Tank.
Place the Waste Holding Tank in an upright
position (Pull-Out Handle at the top, Wheels
at the bottom). Slide the handle sideways - to
the front of the tank - until it snaps out of its
locked position. Pull the handle up and wheel
the Waste Holding Tank to an authorised
waste disposal point. Push the handle back
into its locked position. Turn the emptying
spout upwards and remove the cap from the
spout.
Hold the Waste holding Tank in such a way
that during emptying you can operate the
vent plunger with your thumb. To empty the
tank without splashing, depress the vent