Bailey Orion Owner'S Manual Download

Page: 98 / 102

5-13

General

5.6.6

FAULT -

Trailer brakes inoperative

Cause

Cure

Brakes underadjusted.

Check action and rectify.

Lining contamination.

Replace brake shoe assemblies.

Seized cables.

Free off or replace.

Linings worn out.

Replace brake shoe assemblies.

5.6.7

FAULT -

Hot brakes

Cause

Cure

Brakes overadjusted.

Re-adjust as described.

Pull-off spring broken.

Replace spring.

Seized cables.

Free off or replace.

5.6.8

FAULT -

Handbrake will not hold trailer on slope

Cause

Cure

Incorrect adjustment at spring cylinder.

Re-adjust as described.

5.7

REFRIGERATOR - FAULT FINDING

5.7.1

FAULT -

No 230V fridge operation

Cause

Cure

230V socket that the fridge is plugged

Usually located either under the oven or in the

into not connected or switched on.

front bunk. Check plug is located correctly and
turn on the switch.

Summary of Contents for Orion







































































































Search results

Summary of Contents for Orion

Reviews:

Related manuals for Orion

Brands by name

Popular brands

Bailey Orion, Owner'S Manual

Search results

Summary of Contents for Orion

Reviews:

Related manuals for Orion

Brands by name

Popular brands