Bailey Orion Owner'S Manual Download

Page: 31 / 102

3-2

Caravan Service Systems

3.1.3

Troubleshooting

FAULT

CAUSE

SOLUTION

Pump doesn’t run

No power to pump

Check power supply
Attach leads/clean connections

Fuse has blown

Replace fuse do not exceed recommended fuse size.

Blockage in pipework

Check pipework for kinks.

Pump runs but no water

No water getting to pump

Check water tank is not empty.

Remove each valve lever, tighten the nut located below the
valve lever and replace the lever.

Check all connections from tank to inlet of pump are secure,
any air leaks will prevent prime. To test for air leaks hold
showerhead underwater and operate pump. If air bubbles are
visible coming from the showerhead an air leak is present.

Water leaking at outlet

Check pipework/fittings for leaks and repair.

side of pump

Check system drain plugs are closed.

Pump runs but will not

Water leaking at outlet

Check pipework/fittings for leaks and repair.

switch off

side of pump

Check system drain plugs are closed.

No water

Check water supply level.
Check and replace filter if clogged.

Pump cycles on and off

Water leaking at outlet

Check pipework/fittings for leaks and repair.

periodically when all the

side of pump

Check system drain plugs are closed.

taps are closed. (Normal
with partially opened tap)

Pump cycles on and off

Excessive back

Check pipework for kinks and filters etc., are clear.

excessively when tap/s

pressure

Check shower rose/taps for blockages and repair.

are open

Low flow

Bore of pipework/

Check for kinks in pipework.

connections too small

Check pipework is not blocked.

Power supply to the

Check battery is not discharged.

pump

Pipework/connections

Replace damaged connections.

crushed due to
overtightened jubilee
clips

Water leaking at outlet

Check pipework/fittings for leaks and repair.

side of pump

Check system drain plugs are closed.

Pump internal filter

Remove fitting connected to pump inlet, using point nosed

clogged (if present)

pliers remove cylindrical filter mesh from inside pump inlet.
Clean and refit filter and plumbing.

appears

Summary of Contents for Orion







































































































Search results

Summary of Contents for Orion

Reviews:

Related manuals for Orion

Brands by name

Popular brands

Bailey Orion, Owner'S Manual

Search results

Summary of Contents for Orion

Reviews:

Related manuals for Orion

Brands by name

Popular brands