Bailey Orion Owner'S Manual Download | Manualshive

Page: 54 / 102

background image

4-11

Caravan Equipment

4

4.5.2

Oven

1. Ensure the gas cylinder is connected and turned on. In the event of a gas smell turn off at gas

cylinder and contact supplier.

2. Remove all accessories and packing that may be in the oven and clean the interior before using it for

the first time. Use warm soapy water and rinse carefully.

3.

To light :

Open door, push in the control knob and turn to gas mark 9. Hold a lighted match or taper

to the burner and push the control knob in and hold. The burner should ignite and the control knob
should be held in for 10-15 seconds before release. If the burner goes out, repeat procedure holding
control knob for slightly longer.

4. For models fitted with Spark Ignition the procedure is similar except that the burner can be ignited by

depressing the ignition button which is located on the fascia. Ignition must be carried out with the
door open, and if the burner has not lit within 15 seconds the control knob should be released and
the oven left for at least 1 minute before a further attempt to ignite the burner.

5. Place the oven shelf in the required position and close the door. Set the control knob to approximately

gas mark 5 and heat the oven for about 30 minutes to eliminate any residual factory lubricants that
might impart unpleasant smells to the meals being cooked.

6. Although the oven does heat up quickly, it is recommended a 10 minute preheat be allowed. The

oven should reach full temperature in about 15-20 minutes.

7.

To turn off :

turn the control knob until the dot on the control knob is aligned with the dot on the

control panel.

8.

Flame Failure Device (FFD) :

the oven burner is fitted with a flame sensing probe which will

automatically cut off the gas supply in the event of the flame going out.

9.

Oven shelf :

the oven shelf is designed to allow good circulation at the rear of the oven and is fitted

with a raised bar to prevent trays or dishes making contact with the back of the oven. Additional
shelves are available through our local caravan retailer.

«
...
52
53
54
55
56
...
»

Summary of Contents for Orion







































































































Reviews:

No comments

Related manuals for Orion

Brand: Airstream Pages: 104

Dexter 580 2020

Brand: Karmann-Mobil Pages: 75

2005 Alpine Coach

Brand: Western Recreational Vehicles Pages: 124

Brand: Jamboree Pages: 56

Brand: Jayco Pages: 169

Legacy Fifth Wheel 2009

Brand: Jayco Pages: 132

Chalet 27CR2006

Brand: Winnebago Pages: 116

2016 Minnie Winnie

Brand: Winnebago Pages: 126

Brand: Winnebago Pages: 185

Brand: Roadtrek Pages: 32

Brand: Roadtrek Pages: 51

Brand: Roadtrek Pages: 82

Brand: Roadtrek Pages: 93

Brand: Roadtrek Pages: 125

Brand: Roadtrek Pages: 136

2014 F-Series Super Duty

Brand: Ford Pages: 143

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands