manualshive.com logo in svg

Baicells Nova430i, Installation Manual

Share
Download
Baicells Nova430i Installation Manual Download Page 4

 

4 

Table of Contents 

1 Overview .................................................................................................................................. 7

 

1.1 Introduction .................................................................................................................... 7 
1.2 Features.......................................................................................................................... 8 

2 Installation Preparation .......................................................................................................... 10

 

2.1 Materials ...................................................................................................................... 10 
2.2 LEDs and Interfaces ....................................................................................................... 12 
2.3 Location and Environment ............................................................................................ 13 
2.4 CloudCore Account ....................................................................................................... 13 

3 Installation .............................................................................................................................. 14

 

3.1 Process Overview .......................................................................................................... 14 
3.2 Install eNB on Pole or Wall ............................................................................................ 14 

3.2.1 Install on Pole ..................................................................................................... 14 
3.2.2 Install on Wall ..................................................................................................... 16 

3.3 Connect Cables ............................................................................................................. 17 

3.3.1 Cable Laying Requirements ................................................................................. 17 
3.3.2 Connect Ethernet Cable ...................................................................................... 18 

3.4 eNB Grounding ............................................................................................................. 18 

3.4.1 Connect Grounding Cables ................................................................................. 18 
3.4.2 Pole Grounding................................................................................................... 19 

3.5 Maintenance Chamber Waterproofing .......................................................................... 20 
3.6 Power on to Check LED Status ....................................................................................... 20 
3.7 Configure Basic Parameters ........................................................................................... 21 

3.7.1 Launch the eNB GUI ........................................................................................... 21 
3.7.2 Upgrade Firmware .............................................................................................. 23 
3.7.3 Basic Configuration Overview ............................................................................. 24 
3.7.4 Configure Network Interfaces ............................................................................. 24 
3.7.5 Configure the Management Server ..................................................................... 29 
3.7.6 Configure Quick Settings..................................................................................... 31 
3.7.7 Configure Carrier Setting .................................................................................... 32 
3.7.8 Reboot ............................................................................................................... 33 
3.7.9 Verify eNB Operational Status ............................................................................ 34 

Appendix: Regulatory Compliance ............................................................................................. 37

 

FCC Compliance .................................................................................................................. 37 
ISEDC Compliance ............................................................................................................... 37 

 
 

 

Summary of Contents for Nova430i






































Reviews:

No comments

Brands by name

Popular brands

Load more brands