manualshive.com logo in svg

Baicells Nova430i, Installation Manual

Share
Download
Baicells Nova430i Installation Manual Download Page 26

 

26 

Field Name 

Description 

MTU 

Used to specify the maximum size of the network layer protocol data unit 
that can be communicated in a single network transaction. Range is 700 
to 1600. 

DNS Address 1 

Used to define the DNS 1 IP address 

DNS Address 2 

Used to define the DNS 2 IP address 

WAN Config 

Used to enable the interface. Four IP addresses are the maximum number 
the eNB supports. 

IP Access Mode 

Used to select the desired interface protocol: DHCP, Static IP, IPv6 DHCP, 
or IPv6 Static IP 

Current IP 

The WAN interface IP address 

Option60 

Used to differentiate between different terminal when 

IP Access Mode

 is 

set to 

DHCP

 

Subnet Mask 

Used to define subnet mask address if 

IP Access Mode

 is set to 

Static IP

 

Prefix 

Prefix of IPv6 address for WAN interface if 

IP Access Mode

 is set to 

IPv6 

Static IP

 

Gateway 

Used to define gateway address if 

IP Access Mode

 is set to 

Static IP

 

VLAN ID 

Used to configure more IP addresses for the 

WAN

 interface through the 

VLAN when there is a need to transmit multi-types of data. 

 

3.7.4.2  

 

LGW 

The Local GateWay (LGW) setting must be configured when using the Baicells CloudCore Evolved 
Packet Core (EPC).

 

Refer to Figure 3-15 and Table 3-2. You must reboot the eNB when you make 

changes to these settings.

 

Figure 3-15: LGW 

 

Table 3-2: LGW 

Field Name   

Description   

LGW 

On or Off 

Summary of Contents for Nova430i






































Reviews:

No comments

Brands by name

Popular brands

Load more brands